Votes - 4, Average rating: 4.8 ( )

Manafacture: Citizen File size: 1.48 mb File name: Language of manual:

The changed set value is printed. (When change of set value is repeated, the original set value is recovered). When you press the FEED button long, the set value is accepted and then the printer goes to the next setting item. 5. Returning to the memory switch select mode When the setting of the desired content is completed, open the printer cover and then close the printer cover. This allows the printer to print the setting of the changed memory switch. 6. Saving the setting and exiting the memory switch setting mode Press the FEED button short to move to “Save To Memory”. Then press and hold the FEED button. The printer prints the content of new setting and exits the memory switch setting mode to return to the normal standby state. * Unless saving the setting is executed, the changed setting cannot be enabled. 7. Initializing the memory switch When you want to return the memory switch setting to the initial state, go to “Save To Memory” in the above procedure. Here, open the printer cover and press and hold the FEED button till buzzer sounds. This allows the printer to return to the initial state. * All the memory switches settings are returned to the factory set values. — 25 — 5.4 Selecting Paper Type*L 5.4 Selecting Paper Type*L Paper type selection is available by the combination of memory switches SW4-4 and SW4-5 by the used of “Memory Switch Select Mode”. In addtion, the following procedure is available. 1 Enter Selecting Paper Type mode. 1)Open the printer cover and remove paper. Pressing and holding the FEED button, turn the printer power ON. The POWER LED starts blinking. 2)Release the FEED button and then close the printer cover. Buzzer sounds and the paper type currently set is indicated by the LED on the operation panel. 2 Select Paper Type. Press the FEED button to match the paper type loaded to the LED indications in the table below. (Refer to the table below.) Label POWER LED ERROR LED Green lit (OFF) Thermal paper roll (OFF) Red lit Black mark paper Green lit Red lit 3Save the selected Paper Type to the Printer. Open and close the printer cover. By this operation, selected paper type is stored in the printer memory and the Selecting Paper Type mode is terminated. Since then, "P.Length Set" of Memory switch 4-1 becomes disable. When closing the printer cover during the setting a black mark paper or label paper in the printer, paper length is measured, and the result will be printed out. * When paper detection error occurs at the measurement of paper length, automatically enters paper sensor adjustment mode. Adjust the sensor in accordance with “5.5 Adjusting the Sensitivity of Paper Sensor”. 5.5 Adjusting the Sensitivity of Paper Sensor*L Before using black mark paper (BM paper) or label paper, adjust the sensitivity of the paper sensor by using actual paper. 1 Enter Adjusting Paper Sensor mode. Open the printer cover, remove paper, and then set the printer power switch to ON. Here, POWER LED and ERROR LED go on with the buzzer sound. Then close the printer cover while pressing the FEED button. The ERROR LED starts blinking with the buzzer sound. — 26 — 2 Set paper to the printer. This printer has three types of built-in paper sensors. In case of label, set it so that label is positioned on the label light receiving sensor and label light emitting sensor. In case of black mark paper, set it so that the printable portion (other than black mark) is positioned on the black mark sensor. With this state kept, closing the printer cover causes ERROR LED to blink with the buzzer sound. Label light receiving sensor Black Mark sensor(BM2) Black Mark sensor(BM3) Label light emitting sensor Black Mark sensor(BM1) 3Adjust the sensitivity of the paper sensor and measure the length of paper. Pressing the FEED switch causes label to be fed and paper sensor sensitivity adjustment and paper length measurement are carried out automatically. If the FEED button is pressed during the paper measuring, the result will be printed out as follows, and the printer memory switch will be initialized. * The measuring result is a reference value showing a label length showing a gap between labels < Example of label measuring result > — 27 — 5.6 Printing Paper*L 5.6 Printing Paper*L Also refer to the core dimension and notes of “5.2 Printing Paper” in User’s Manual of standard model. Use print paper shown in the following table or the equivalent. Paper type Product name Recommended thermal label paper GG40/P22/G6B from Ojitac, HD75 from Nippon Paper, 150LA-1 from Ricoh Printing surface a) Label paper .102 or less DLMBCAEFHIJKGFull cut position Paper feeding direction Printable area Roll paper specifications Label paper thickness* 65 to 85 .m Liner thickness 60 .m max Core inner diameter d 25.4mm Core outer diameter D 32mm Unit: mm Mark Item Dimensions A Liner width 57.5, 59.5, 79.5, 82.5 + 0.5_ B Label width (Size A) -4 + 0.5_ C Left edge of label 2 + 0.5_ D Print width (Size A) -8 E Top margin 2 + 1_ F Print length 21 to 29...

Download now

Please, enter two numbers from picture: