For convenience, if one of the bulbs burns out, it may be a good idea to replace all of the light bulbs. 1. Turn off power to the unit by unplugging the power cord. 2. Let fireplace cool if it has been operating. 3. Remove the two screws on the top corner of screen. Pull the screen upward slightly, and then pull out. 4. Remove the four screws that secure the log set/ember bed in position. 5. Remove log set / ember bed and grate assembly. 6. Examine the bulb(s) to determine which bulbs need to be

WHAT TO DO IF YOU SMELL GAS: .. Do not try to light any appliance. .. Do not touch any electrical switches; do not use any phones in your building. .. Immediately call your gas supplier from a neighbor’s phone, follow the gas supplier’s instructions. .. If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency or the gas supplier. WARNING: Improper installation, adjustment, alteration, service, or maintena

ELECTRICAL WIRING DIAGRAM Any electrical repairs or rewiring of this unit should be carried out by a licensed electrician in accordance with national and local codes. If repairing or replacing any electrical component or wiring, the original wire routing, color coding and securing location must be followed. 5 MAINTENANCE OF MOTORS The motors used on the fan and flame generator assembly are prelubricated for extended bearing life and require no further lubrication. However, periodic cleaning/vacu

10. Do not run cord under carpeting. Do not cover cord with throw rugs, runners or similar coverings. Arrange cord away from traffic areas and where it will not be tripped over. 11. To disconnect heater, turn controls to OFF, then remove plug from outlet. 12. Connect to properly grounded outlets only. 13. When this appliance is installed, it must be electrically grounded in accordance with local codes with the current CSA C22.1 Canadian local codes for USA installations. Follow local codes and N

Apply Teflon tape or pipe dope to the steel fittings before making any connection. BE CAREFUL! Make sure all gas connections are snug, but not over tighten! 2. Extend the gas supply system using1/2” black iron pipe from current house supply. This may be accomplished by a teeing off” or tapping into a convenient gas line connection; installing the necessary pipe for the distance required; and then installing a manual valve at exterior house wall. If pipe is to pass though a foundation or house wa

(2) Flame brightness Press “SET”button, when the lamp symbol flashes, press button to decrease the flame brightness and button to increase the flame brightness. 7. For Flame Effect only: Select MANUAL mode, then set the Heating level to no heating level or select AUTO mode and then set temperature to lowest setting. 8. Manual ON/OFF button If you can’t find your Remote Control or the Remote Control is damaged, you can use manual ON/OFF button to manual turn on/turn off your heater. 2. The Clock

(See FIG 4). Installing logs for SFE23RE: 4.Insert the pin on log 6 to the recessed hole on log 4, and place log 6 as figure shows. (See FIG 9). Installing logs for SFE33RE: FIG 1 - Logs for SFE23RE 1.Insert the two pins on log 1 to the two recessed holes at the middle of grate. (See FIG 2). 2.Insert the pin on one end of log 2 to the recessed hole on log 1, with the other end of log 2 placed on the ember bed (where marked). (See FIG 3). FIG 5 - Logs for SFE33RE 1.Place log 1, log 2 and log 3 in

MOVABLE AND WALL-OR CEILING HUNG ELECTRIC ROOM HEATERS INSTALLER: DO NOT DISCARD THIS MANUAL-LEAVE FOR HOME OWNER Freestanding Electric Fireplace SFE33RE-W SFE33RE-C SFE33RE-O SFE33RE-DO SFE23RE SHOWN WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, A FIRE MAY RESULT CAUSING PROPERTY, PERSONAL INJURY OR LOSS OF LIFE. FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE PC-FE23A610-0506 Important Instru

WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in your building. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency, or gas supplier. WARNING: Improper installation, adjustment, alteration, service or maintenance can cause in

WARNING: This is an unvented gas- fired heater. It uses air (oxygen) from the room in which it is installed. Provisions for adequate combustion and ventilation air must be provided. Refer to Air For Combustion and Ventilation section on page 4 of this manual. Do not store, or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WHAT TO DO IF YOU SMELL GAS Do not try to light any appliance. Do not touch any electrical switch; do not use any phone in