No. Description 1693847 5HP Rear Tine Tiller 6.5HP Rear Tine Tiller Mfg. No. Description 1693848 6HP Rear Tine Tiller 1721526-00 Rev 1/2001 TP 10 0-24 85-0 0-RT-S O Simplicity MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 © Copyright 2001 Simplicity Manufacturing, Inc. All Rights Reserved. Printed in USA. Table Of Contents TABLE OF CONTENTS.........................................1 OPERATION SAFETY...........................................2 Own

* Cover—on pre-printed two-tone “Swash” stock. Press: * Body—1-color, 2-sided * Cover imprint —1-color, 1-sided Bindery: * Saddle Stitch, Face Trim * Face Trim COVERS: * This file may contain several manuals, which differ only in their covers. * Covers are all present at the beginning of this file. * Back cover for a particular manual is the page IMMEDIATELY AFTER the front cover. • Check the front cover for the individual part number (typically a 171xxxx number). BODY: • The body of the manual

Lock with jam nut so that . bars are free to swing. 2. Attach depth crank (2) at (3) and (3). Adjusting nuts should be equally spaced on threads. 3. Clamp wheel standards to draw bar assembly as shown at (4) and (4). 4. Clamp gang tool holders to tool bar as shown at (5) and (5). 5. Attach the four tool standards to the right and left tool frame assemblies as illustrated at (6). 6. Assemble upper and lower tool control handle as shown. 7. Attach tool handle assembly (7) to draw bar assemb

Standard, 32-1/2 In. with Tine Extensions TILLING DEPTH 0 to 7 Inches, Adjustable ATTACHMENT TO HUB: Bolted TO SHAFT: Pin and Spring Clip DRIVE INNER: Pin Type Floating Drive OUTER: Pin and Torsion Plate Floating Drive SPEED 75 RPM at Full Engine Speed DEPTH BAR TYPE Pivots in Reverse ATTACHMENT Pin and Spring Clip ADJUSTMENT 0 to 7 Inches Tilling Depth CONTROLS LOCATION FORWARD CLUTCH: Right Handle, Top REVERSE CLUTCH: Left Handle, Bottom THROTTLE: Center Mounted HA

443 12345A7&90 PRIKTeO IN U.S.A. SIMPLICITY MANUFACTURING COMPANY. 1 2 9 U ASSEMBLY The cart enclosure for the vacuum collector consists of a metal framework and a canvas cover, all of which fits on the dump cart body. Here follows step by step illustrations showing the sequence of assembly for this unit« A. The enclosure should be constructed or the cart ■body, starting with the lower channel members shown in Figure 1. The front support assembly la then added as shown In Figure 2. (Refer

Place the pivot pin through the blade assembly bracket and push bar. Position the push bar under the tractor front axel and attach it to the axel using two pins and spring clips. Attach the spring end of the lift rod to the push bar assembly and the other end to the tractor lift arm using two spring clips. OPERATION Alternate holes are provided to permit adjustment of the shoe assemblies for raising or lowering the blade when cleaning gravel drives or walks. When cleaning concrete it is desira

• Slide the rubber dust cover (F) over the plastic fitting (B). 2 3 8 Figure 7 TP 1000-4518-01-LW-S Form No. 173xxxx-00 Two-Stage Snowthrower 1694986 10530L, 10.5 Snowthrower B A A C D B D Figure 3 A B C A B C D A B D E C D B A A B Remove Snowthrower From Crate • Cut the two zip ties from between wheels and the wood pallet. • Remove screws (A, Figure 11) from both skid shoes (B). • Roll snowthrower off crate. Add Oil and Fuel Note: Engine is NOT shipped with oil. Add 5W-30 premium engine oil. Se

Store the spring clip in the lift rod hole. 4. Push the belt tensioning lever down. 6 Installation & Removal 5. Remove the belt from the PTO pulley (A, figure 5) and from the two idler pulleys (B & C). If a mower attachment is to be used on the tractor, remove the front idler pulley (D, figure 4) and install it in upper tab. 6. Remove the snowthrower from the tractor by using either one of the following methods “a” or “b”. (The belt may remain on snowthrower pulley unless removal is desired

1/4 pages 8 & 7. 5 Simplicity Frame. Handle & Shroud Group T 76 Tighten nut (Raf. No. iß) 3 It lbs. max. Clutch lever must pivot frcoly. NOT£ U*e standard hardware torque spec. 173209 unless otherwise noted. A*fe to bottom out In palnut (Ref. No. 23). Mfg. No. 1690901 Ä 1690902 Frame. Handle & Shroud Group Simplicity Ref. No. Part No. Qty. Description 31 1664804 1 SWITCH, Ignition 32 916906 1 LOCKWASHER, Int Tooth. 5/8 33 933741 NUT. Speed, "U", #10 34 1664817 1 GUIDE. Choke K