If you have any questions relative to its application DO NOT use the tool until you have written Porter- Cable and we have advised you. Technical Service Manager Porter-Cable Corporation 4825 Highway 45 North Jackson, TN 38305 1. USE SAFETY GLASSES. To prevent eye injuries, the tool operator and all persons in the work area must wear safety glasses with permanently attached, rigid, plastic side shields. These safety glasses must conform to ANSI Z87.1 requirements (approved glasses have “Z87” pri

5. Foreign materials of a conductive nature such as, but not limited to, steel wool, aluminum foil, or any buildup of metallic particles should be kept away from charger cavities. Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean. 6. Do not freeze or immerse charger in water or any other liquid. : Shock hazard. Do not allow any liquid to get inside charger. : Never attempt to open the battery pack for any reason

The Model and Serial No. plate is located on the main housing of the tool. Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ Type ___________________________________________ Serial No. _______________________________________ Copyright © 2003 Porter-Cable Corporation Part No. 904034 - 12-02-03 SAFETY GUIDELINES - DEFINITIONS This manual contains information that is important for you to know and understand. This information r

The swivel end must be used to attach high pressure hose to hose reel, see below to determine fixed and swivel ends. If quick connect socket is assembled on swivel end, remove and connect it to fixed end of hose. hose end without swivel hose end with swivel 6. Feed high pressure hose through slot (1) in flange assembly and connect to swivel (2). Tighten securely. 3. Apply sealant tape to hose reel inlet hose and assemble quick connect to hose reel inlet hose. 1 2 7. Make a loop in hose as shown.

7. To remove disc, peel disc away from pad. NOTE: Do not store machine with an abrasive disc installed. Heat generated by the sanding operation increases the adhesive bond between the disc and pad. If disc is left on pad for an extended time after use, it can become difficult to remove. 10 Fig. 2 Fig. 3 Models 333 and 333VS: 1. DISCONNECT TOOL FROM POWER SOURCE. 2. Place machine on workbench with pad up (see Fig. 3). 3. Clean dust from pad face. 4. Position Hook & Loop Abrasive Disc onto sander

When the air compressor reaches “cut-out” pressure, the check valve “closes”, allowing air pressure to remain inside the air tank. ON/AUTO - OFF Switch (C) Fig. 3: Turn this switch ON to provide power to the automatic pressure switch and OFF to remove power at the end of each use. Pressure Switch (D) Fig. 1: The pressure switch automatically starts the motor when the tank pressure drops below the factory set “cut-in” pressure. It stops the motor when the air tank pressure reaches the factory s

Always unplug the charger from the power supply when there is no battery pack in the cavity. Unplug charger before attempting to clean. • DO NOT attempt to charge the battery pack with any chargers other than the ones in this manual. The charger and battery pack are specifically designed to work together. • These chargers are not intended for any uses other than charging designated PORTER-CABLE rechargeable batteries. Any other uses may result in risk of fire, electric shock or electrocution. •

Only use a moist cloth to clean the motor unit. Warning - Check if the voltage indicated on the appliance corresponds to the local mains voltage before you connect the appliance. - Do not use the appliance if the plug, the mains cord or other parts are damaged. - If the mains cord is damaged, you must have it replaced by Philips, a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard. - Never let the appliance run unattended. - This appliance is no

Shut off the pressure washer and turn off the water supply. 2. Pull trigger on gun handle to relieve any water pressure. 3. Disconnect the spray wand from the gun. 4. Remove the high-pressure nozzle from the spray wand. Remove any obstructions with the nozzle cleaning tool provided and backflush with clean water. 5. Direct water supply into spray wand to backflush loosened particles for 30 seconds. 6. Reassemble the nozzle to the wand. 7. Reconnect spray wand to gun and turn on water supply. 8.

11- ENG D25806 TO SHUT DOWN IMPORTANT: Read and understand how to shut down the pressure washer before operating. 1. If you have siphoned chemicals, siphon a bucket of clean water through the chemical hose. NOTE: Failure to do so will cause damage to the pump. 2. Refer to engine manual for correct engine shut down procedure. NOTE: NEVER turn the water off with the engine running. 3. Turn water source off. 4. Pull trigger on spray gun to relieve any water pressure in hose or spray gun. 5. See Sto