Package Contents • LINDY HDMI 1.3b Splitter • 5V DC Multi Country PSU • This manual Features • HDMI 1.3b, HDCP 1.1 and DVI 1.0 compliant • Deep colour up to 8 & 12 bit, 1080p (24/60Hz) • Splits a single HDMI source without any signal loss for use with up to 8 displays • Supports multi-channel audio: o LPCM 7.1CH o Dolby TrueHD o Dolby Digital Plus o DTS-HD Master • When used with computers, supports DVI-D resolutions up to UXGA (1600 x 1200) • Supports xvYCC and CEC bypass • Built in EDID simula

20704 © LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH -FIRST EDITION ( Jul 2001) Module Cover Terminals 2-Port-PCB Chassis Shielding Contact Strain Relief Ground Connector PCB-terminals optimised for fast data transfer Strain relief’s are attached - so they won’t get lost Additional strain relief by use of a cable tie is possible Foil- or Braid shielded cable Module Cover Terminals 2-Port-PCB Chassis Shielding Contact Strain Relief Ground Connector PCB-terminals optimised for fast data trans

Reliable operation can only be guaranteed if the instructions are followed correctly. Please check the installation location carefully in advance in case there are any electrical installations behind the wall or above the ceiling! In case of alarm a very loud sound is emitted. Do not switch the unit on in close proximity to anybodies ears! Keep away from children! This smoke detector is a photo electric sensor with integrated relays to connect to any alarm control system such as the RMS. When sm

Wind the shielding wire around the 10mm left of the shielding, it will be clamped later beneath the strain relief. untwist 13 mm at most If present, shorten the shielding foil of the single pairs (Pimf-cable only) to the same length. Untwist the pairs for 13mm at most and connect the wires using the following colour scheme NEXT – Pairs 1,2 – 3,6 NEXT – Pairs 3,6 – 4,5 English Manual Mounting 1. Mount the strain relief and the shielding braid or 2. Connect the individual wires foil as shown in th

This card is equipped with two high speed RS-232 serial interfaces and one 1284 centronics parallel interface. The serial ports include 16Byte FIFO with speeds up to 430Kb/Sec and up to 1.5MB/Sec on the Parallel port. Port Specification Serial Port: · Chipset: MosChip MCS9901, 16Byte FIFO · Compatible chips: with 16C550 and 16C450. · IEEE standard: RS-232 Interface · Max. Speed: Bi-directional speeds from 50 bps to 16Mbps/port Parallel Port: · Chipset: MosChip MCS9901 · IEEE standard: IEEE 1284

To do this, hold down the central button or wheel button and click the right hand button. Hold down centre button ( ). Press and release left hand button ( ) to launch the on-screen menu When the menu is first called up, a set of default names will be listed. You will probably want to change these names to suit your computers (see section 3.5). When you launch the on-screen menu you will see a screen similar to that shown below. LINDY CPU Switch Dual Multi-Platform Installation and Use Page 47 T

32916 a Fffi © LINDY ELECTRONICS LIMITED & LINDY-ELEKTRONIK GMBH - FIRST EDITION (March 2008) User Manual English Introduction The LINDY FireWire Repeater Hub adds IEEE-1394a compliant ports that support data transfer rates of 100, 200 and 400 Mbps, and automatically switch to the highest speed that the peripheral supports, to your computer. Package Contents ■ LINDY FireWire Repeater Hub ■ FireWire Cable ■ Power Adapter (Multi-country) ■ This manual System Requirements ■ Pentium I

It DOES NOT change the voltage! Before use, please ensure your electrical equipment complies with the voltage of the country you are in. For temporary travel use only; not for permanent use! Keep out of reach of children! No. 73013 April 2006 www.lindy.com

1 Features................................................................................................................. 1 Technical Specifications...................................................................................... 2 System Requirements..........................................................................................2 Package Checklist ................................................................................................ 3 Installation and Connections.....