At power up or in an idle condition, this value should be in the range of 060 to 065. A reading of 175 is high and could decrease the life of the printhead. An average amount of printing will give readings that range from 070 to 120. Pot -this reading comes from the darkness potentiometer located on the front panel board. It will vary from 000 (darkest) to 255 (lightest). Adjust this value for a midrange value of 128. TOFA -(Top of Form Adjustment) determines where the first position of print be

2) Close the printhead. CALIBRATING PLEASE WAIT The printer automatically adjusts the scale (gain) of the signals it receives from the media and ribbon sensors based on the specific media and ribbon combination you are using. On the sensor profile, this essentially corresponds to moving the graph up or down to optimize the readings for your application. ---RELOAD ALL When .RELOAD ALL” is displayed: 1) Open the printhead and pull the media forward until a label is positioned under the media senso

See page 16. Calibrate the printer (see page 17). Brady X-PLUS Series User.s Guide Error Condition Head Open Problem Solution The printhead is not fully closed. Close the printhead. Error Condition Head Element Bad Problem Solution One or more of the printhead elements have failed the printhead element test. If the failed elements impact your printing application, replace the printhead. To override this error, disable the head test count feature on the front panel by defaulting the value to .000

PRINTER OVERVIEW General Features/Unique Characteristics .............................................................2 Operating Requirements .......................................................................................3 Label Dispensing/Print Requirements ...................................................................4 User Interface Controls .........................................................................................5 Sensors.........................................

Default: Web Selections: Web, mark This parameter tells the printer whether you are using media with a web (gap/space between labels, notch, or hole) to indicate the separations between labels or if you are using media with a black mark printed on the back. If your media does not have black marks on the back, leave your printer at the default (web). PRINT METHOD Selecting Print Method Press the RIGHT BLACK OVAL key for the next value; press the LEFT BLACK OVAL key for the previous value. Default

2 Features ......................................... 3 Notes ............................................ 3 Repair Policy .................................. 3 Specifications ................................. 3 Set-up ............................................ 4 Operation/Adjustments ................... 5 Maintenance .................................. 6 Legend ........................................... 6 Exploded View ............................... 7 WARRANTY POLICY FOR DSP SERIES LABEL DISPE

±0.039" (±1.0mm) on noncontinuous media Horizontal . ±0.039" (±1.0mm) within a roll of media • Programmable print speeds: - 203 dpi models = 2.0" (51mm) through 10" (254mm) per second in 1" increments - 300 dpi model = 2.0" (51mm) through 6" (152mm) per second in 1" increments MVP Series Product Guide Page 18 Printer Specifications Media Specifications • Maximum label length: 39" (991mm) • Media type: continuous, die-cut, tags, black- mark • Media web width (label and liner): 1.0" (25.4mm) to 4.

(Fo. Serial-Interfac. Printer. Only. The M-Series Printer, with the RS-232 Serial Interface, uses eight miniature switches located on the rear of the printer, above the Signal Interface Cable Connector. The ON/OFF positions of these switches establish some of the Printer Configuration Parameters. Bank 1 switches must be properly positioned to establish serial data communications with the host computer. Thereafter, the position of these switches should not be changed. Note: Parallel-interface pri

Customer order # 11342L-12 Manufacturer part # 11342LB-12 Rev. 1 . This manual contains proprietary information of Brady Corporation. It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the expressed written permission of Brady Corporation. . Continuous improvement of products is a policy of Brady Corporat

These characters are available in fonts 1–6 and 9. Getting Started 13 _______________________________________________________________________ 14 Getting Started 2.4 Memory Cartridges The Printer has one standard memory cartridge slot. The primary use of the memory cartridges is for storing label formats, graphic images, fonts and for internal batch. Follow the instructions outlined below when installing memory cartridges. 1. Ensure that all printing has been completed. 2. Open the Side Access Co