File these instructions with the owner or maintenance department. P.O. Box 309, Menomonee Falls, WI 53052-0309 215-1384Rev.A;EN01-819 TEL. 1-800-BRADLEY FAX (262) 251-5817 Page1of4 Express® LavatorySystemMG-SeriesExtension MG-EXT InstallationInstructions Pre-Installation Information Check Contents Separate all parts from the packaging and check each part with the drawing below. Make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not attemp

. . . . . . . . . . . . . .2 HN-200 Column Shower Components and Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . .2 Installation Instructions Type AColumn Shower . . . . . . . . . . . . . . . . . .3 Supplies from Below/Vent Off Line Type B Column Shower Installation . . . . . . . .4 Supplies from Above/Vent Through Column Type H Column Shower Installation . . . . . . . .5 Supplies from Below/Vent Through Column Type O Column Shower Installation . . . . . . . .6 Supplies from Above/V

1 Enable “Manual Setting” Mode > See “Enabling Manual Setting Mode” section 2 Fully cover sensor with hand. Water fl ow stops after 5 seconds - Continue to hold on for another four (4) additional water pulses. 3 Remove hand. Result: Scrub Mode is now activated for 180 seconds. F - Sensor Range Adjustment The detection distance of the sensor can be adjusted between approximately 4 - 11 inches from the infrared window. 1 Enable “Manual Setting” Mode > See “Enabling Manual Setting Mode” section 2 R

O.D. washers to mount main frame and bowl to wall (minimum pull-out rating of 1,000 lbs.) • (2) #10 wall anchors (for optional mixing valve/bracket mounting) • 1/2" NPT hot/cold or tempered supply piping • 1-1/2" NPT drain piping • OPTIONAL: 110 volt GFCI protected electrical outlet for 100–120 VAC plug-in transformer (for Bradley Faucets) • OPTIONAL: 240/208 or 277 volts for electric tankless water heater Installation FL-1H, FL-1L Cleaning and Maintenance for Terreon® Material Description: Terr

Terreon® is a unique, cast solid surface material. Aggregate flow and distribution as well as shades of color can vary from product to product creating natural characteristics. Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement, nor does the omission of any brand name cleaner imply inadequacy. Many products named are regional in distribution, and can be found in local supermarkets, department and hardware stores, or through you

Simply omit the steps which do not apply to the unit you are installing. Valve Left/Seat Right version is shown throughout this manual. Valve Right/Seat Left is opposite. Plumbing contractor shall be responsible for installing shower face plate at the correct height to meet accessibility requirements. This installation manual and parts list should be filed by the owner’s maintenance department. Installation Instructions ADA Compliant HN200 Recess-Mounted Shower with • Equa Flo™ • Accu-Zone™ Infr

For more than three washfountains, pipe sizes should be increased proportionately. -Supplies from below or through wall - Vented through ceiling off trap inside pedestal Type O Drain -Supplies from above - Vented from below or through wall off drain (mm) Figure 2d NOTE: Supply lines for one to two washfountains should be 1”; for three washfountains, 1-1/4”. For more than three washfountains, pipe sizes should be increased proportionately. Bradley Corporation • 215-1470 Rev. H; EN 06-915 2/8/07 T

Welded construction with burr-free edges. FLANGE: 22 gauge stainless steel with exposed surfaces in architectural satin finish. One-piece seamless construction, 1" wide with W" return. DOOR: 18 gauge stainless steel with full-length piano hinge and tumbler lock keyed like other Bradley units. PUSH FLAP DOOR: 22 gauge stainless steel with exposed surfaces in architectural satin finish. Self-closing, with heavy-duty stainless steel piano hinge. WASTE RECEPTACLE: leakproof molded plastic. 1.0 g

. . . . . . . . . . . . . . . . . . . . . . . . . .9 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . 10 Care and Maintenance . . . . . . . . . . . . . . . . . 12 Multi-Faucet Transformer Wiring . . . . . . . . . 14 IMPORTANT! Read this entire installation manual to ensure proper installation. When finished with the installation, file this manual with the owner or maintenance department. Compliance and conformity to local codes and ordinances is the responsibility of the installer. Se

Do not disturb sensor scanning procedure (wait until water flow stops and LED switches off) Replace electronics module (See “Replacement Parts”) Change mode or reset sensor (See “Care and Maintenance”) Check external water pressure Provide pressure between 20 - 125 psi Replace solenoid valve (See “Replacement Parts”) Replace electronics module (See “Replacement Parts”) Water runs continuously Water fl ows although shut-off screw is inoperable removed Water drops on infrared window Infrared windo