Dallas, Texas VALUE 10TM CONDENSING UNIT Value 10 condensing units are designed for expansion valve (TXV) and RFC systems. Refer to Lennox engi- neering handbook for expansion valve kits which must be ordered separately. SHIPPING AND PACKING LIST 1-- Assembled 10ACB condensing unit 1-- 45E copper street elbow 1-- RFCIV refrigerant metering device (bullet) 1-- Coupling -- 5/16 x 3/8. (18, 24, 30) Check unit for shipping damage. Consult last carrier immediately if damage is found. GENERAL INFORMAT

A, 05/2007 A French manual is available upon request. Order P/N 775,221CF. Ce manuel d’installation est disponible en francais, simplement en faire la demande. Numero de la piece 775,221CF. In the Commonwealth of Massachusetts: • Installation must be performed by a licensed plumber or gas fitter • See Table of Contents for location of additional Commonwealth of Massachusetts requirements Report No. 050-S-18b-5 Medina™ (MED) WARNINGS • Hot! Do not touch! The glass and surfaces of this appliance w

Complete combustion of the gas requires, but is not limited to, correct gas pressure and gas flow rate, adequate combustion air and proper venting. A WARNING Carbon monoxide gas is invisible, odorless, and toxic. Exposure to carbon monoxide gas can cause personal injury and even death to all occupants, including pets. Any item that is powered by, or gives off heat from, a combustion process (including lawn mowers, automobiles, and fireplaces) has the potential to produce carbon monoxide gas.

1 - Connect test gauge to outlet tap on gas valve. 2 -Disconnect pressure sensing hose from gas valve and plug hose by covering opening with tape or equivalent. Leave barbed fitting on valve open to atmosphere. See figure 35 for differential pressure switch circuitry on 75 kBtuh models. Only 75 kBtuh models are equipped with a secondpressure switch. Other models have single pressure switch. 75 kBtuhDIFFERENTIALPRESSURESWITCHCIRCUITRY BURNER BOX LOW HEAT DIFFERENTIAL PRESSURE BARS SWITCH TEE SOX

However, the unit's performance can be greatly impacted by the individual installation and the operating environment. It is your responsibility to ensure that this appliance is maintained. Proper maintenance is critical for your safety and the satisfactory operation of the product. Lennox strongly recommends annual inspection and maintenance of this appliance. Contact your Lennox dealer for an inspection by a qualified service technician. Lighting Information & Operation AWARNING If you do no

freezing and damage. One 5/8" O.D. copper trap & plastic tubes (3) (furnished) / Pan No. 307g0F089 Date 6-1_9 Supemedes 30790G082 Page T of 12 INSTALLATION Electrical Connections All wiring to unit must comply with the national Electrical Code NFPA No. 70 or local codes, where they prevail. ANY ALTERNATION OF INTERNAL WIRING CAN VOID UNDERWRITER'S APPROVAL, ARI CER TIFICATION AND MANUFACTURE'S LIMITED WARRANTY. The series and rating plates indicate the operating voltages, phase, ampacities and m

Use appropriate safety gear including safety glasses and gloves when installing this equipment. WARNING Risk of electrical shock. Disconnect all remote power supplies before installing or servicing any portion of the system. Failure to disconnect power supplies can result in property damage, personal injury, or death. WARNING Installation and servicing of air conditioning equipment can be hazardous due to internal refrigerant pressure and live electrical components. Only trained and qualified se

In addition, when the unit is recessed, the side walls surrounding the unit must not extend beyond the front edge of the unit (see Figure 3). Back 1/2 (13) Sides 1/2 (13) Top Spacers 0 (0) Floor 0 (0) Bottom of Appliance To Ceiling 64 (1626) Vent 1 (25.4) SERVICE CLEARANCES Feet (meters) Front 3 ft. (0.9 m) Table 5: Minimum Clearances [inches (millimeters)] HEARTH EXTENSION A hearth extension is not required with this appliance. If a hearth extension is used, do not block the control compartment

Note -Installation must conform with these I -External Filter Rack instructions and the installation instructions (Used with kit CAT#16L23 and16L24) packaged with the G26 furnace. 1-Lay G26 unit on its side and cut out return air opening in cabinet. See figure 4. Closet installations -G26 cabinet depth is 2-3/8" 2-Filter rack is shipped for right side installation (60.5ram) larger than G14. The G26 may be installed and for 16 inch (40.6 cm) filter size. If application one inch (25turn) closer to

502,673M SOLID STATE DEFROST Dallas,Texas 9/93 REPLACEMENT BOARD Supersedes 3/92 INSTALLATION INSTRUCTIONS FOR SOLID STATE DEFROST REPLACEMENT BOARD LB-83114C (61H42) USED ON HP7-1, ,/SHIPPINGANDPACKING _ ::::: ] Package 1 of 1 contains: 1-Control board on mounting bracket 1-Defrost thermostat 1-Outdoor fan/defrost relay 8-Wires with 3/16" terminals 1-Screw 2-Wire nuts /tNSTA_TiON: : 1-Turn off power supply to unit. 2-Remove compressor access panel and control box cover. A-Defrost Thermostat 3-D