• Leave this manual with party responsible for use and operation. • Read, understand and follow these instructions for safe installation and operation. DO NOTDISCARD Tested and Listed by Beaverton Oregon USA OMNI-Test Laboratories, Inc. C US OWNER’S MANUAL Installation and Operation Model: 830-0381 3100-I ACT WOOD INSERT Advanced Combustion Technology (ACT) DO NOT DISCARD THIS MANUAL CAUTION • Important operating and maintenance instructions included. • Leave this manual with party responsible f
Please read entire manual before you install and use your fireplace. 4-03 1 480-1081 North Star UEAT EPA Certified Fireplace -N-cilo No one builds a better fire TABLE OF CONTENTS .......Installation and Draft Considerations...................4 A. Listings and Code Approvals...............................3 B. Description of the Fireplace System...................3 C. Fireplace Dimesions, Clearances & Outside Air. 5 D. Chimney Components.........................................6 E. P
4-4 3-4 3-4 3-3 35 ft. 4-4 3-4 3-4 3-3 40 ft. 5-4 4-4 4-4 3-4 V1 H1 Maximum V2 V1 + V2 Min. Elbow only 2 ft. 610 mm * * * 6 in. 152 mm 6 ft. 1.8 m * * * 2 ft. 610 mm 11 ft. 3.4 m * * * 3 ft. 914 mm 16 ft. 4.9 m * * * 4 ft. 1.2 m 20 ft 6.1 m * * * V1 + V2 + H1 = 50 ft (15.2 m) Maximum *No specifi c restrictions on this value EXCEPT V1 + V2 + H1 cannot exceed 50 ft (15.2 m) Note: If the DVP-2SL or DVP-SLP24 adapter is used with SLP pipe, you MUST subtract one number from the table above. Example:
(HHT) fireplaces and is a fireplace part. Refer to the fireplace installation isntructions for the correct accessories to be used. Check with your local building code agency before you begin installation to ensure compliance with local codes, including the need for permits and follow-up inspections. If you encounter any problems regarding code approvals, or if you need clarification of any of the instructions contained here, contact the Heatilator Technical Services Dept., Hearth & Home Technolo
• Range hoods. • Combustion air requirements for furnaces, water heaters and other combustion appliances. • Clothes dryers. • Location of return-air vents to furnace or air conditioning. • Imbalances of the HVAC air handling system. • Upper level air leaks: recessed lighting, attic hatch opening, duct leaks. WARNING Asphyxiation Risk This appliance produces carbon monoxide (CO). • The free opening areas (in square inches) of the chimney damper as shown in the following tables must be met. • User
The blower cord can also be installed on the left side. Disconnect the cord from right side. ROUTE WIRES IN FRONT OF FAN. Re-install on the left side. Do not route cord behind the cooling fan. Figure 15B - Right Side Location FAN (BLOWER) REPLACEMENT Included in Kit: Replacement Blower Tools Needed: 5-32 Wrench and Phillips Head Screwdriver. 1. Remove bolts from both sides of the insert and slide the lower cast cover towards you. See Figure 15D 2. Loosen 4 screws (2 on each side of the motor) th
(32 mm). Effective length is built into this chart. Heatilator • A36R & A42R • 28376 • Rev AF • 11/08 C. Assembling Chimney Sections D. Install Chimney Air Kit WARNING! Risk of Fire! DO NOT install substitute or • Required in Canada. damaged chimney components. • Follow instructions provided with this accessory. • Use only those components described in this manual. Substitute or damaged chimney components could impair E. Installing Ceiling Firestops safe operation and cause overheating and fire.
Igniter Replacement F. Glass Replacement Figure 33.1 Igniter Igniter Bracket Thumb Screw WARNING • • • Glass is 5mm thick high temperature heat- resistant ceramic glass. DO NOT REPLACE with any other material. Alternate material may shatter and cause injury a. Shut down the appliance by turning down the thermostat and let the appliance completely cool down. After the appliance has cooled down, unplug it and remove the ash pan. b. The wire leads to the igniter are connected to the wire harness wi
20802 Kensington Boulevard, Lakeville, MN 55044 USA • 1-888-427-3973 THIS PRODUCT MAY BE COVERED BY ONE OR MORE OF THE FOLLOWING PATENTS: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471, 5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195, 6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413