•Ifusingthetouchscreenmodel(ATM1700T),usethetouchscreentonavigatebyrunningafamiliarprogram. Display PowerButtonPowerIndicatorDISPLAY POWERWARNINGTouch Screen is stillactive while displaypower is offLCD Power Button: MAIN MENUBRIGHTNESS/CONTRAST1280X102463.9KHZ/60HZCOLORPOSITIONSETUPEXITRGBOSD Settings Main Menu: 9. Adjust the Monitor OSD Settings as Required•PresstheSelect(AutoAdj)controlbuttonontherearofthepaneltoinitiateanautomaticconfigurationofthescreen. •Althoughnormallynotneeded,thecontro

com1- 800- 633- 0405AATTLLAASSINDUSTRIALFLATPANELPC MONITORQUICKINSTALLATIONGUIDE-ATM1700/ATM1700T 3505HUTCHINSONROADCUMMING,GA30040-5860,USA TM 1. Verify Contents of the Box: •AtlasFlatPanelMonitor–ATM1700orATM1700T(The“T”attheendofthepartnumberdesignatesthetouchscreenoption.) •VGAvideocable–6’length•RS-232Serialtouchscreencable(ATM1700Tonly)–6’length•USBtouchscreencable(ATM1700Tonly)–2mlength•Mountingclipsandscrews(qtyof14) •USBretentionbracketandmountingscrew(ATM1700T only) •DocumentationandD

... . . ....... . . . . ©Copyright 2005 ATLAS COPCO CONSTRUCTION TOOLS AB 2005-06 NACKA • SWEDEN No 3392 5042 01 1 English ! . INTRODUCTION ....................................................................................................................... 2 SAFETY INSTRUCTIONS ........................................................................................................ 2 Introduction to safety ...........................................................................

For best performance, mount the fixture about 8 ft.(2.4 m) above the ground.NOTE: If fixture is mounted higher than 8 ft.(2.4 m), aiming the sensor down will reduce coverage distance. Wall Mount Eave Mount For under eave installation, the sensor head must be rotated as shown in the next two steps for proper operation and to avoid the risk of electrical shock. For eave mount only: . Swing the sensor head towards the clamp screw joint. Controls Clamp Screw . Then rotate the sensor head clockwise 1

9. Adjust the Monitor OSD Settings as Required•PresstheSelect(AutoAdj)controlbuttonontherearofthepaneltoinitiateanautomaticconfigurationofthescreen. •Althoughnormallynotneeded,thecontrolbuttonsontherearofpanelcanbeusedtomakeotheradjustmentstothescreen. •ConsulttheHardwareUser’sGuide,ATM-19-USER,onthesuppliedDocumentationandDriveCDfordetailedusageoftheOSDsettings. 10. Installation Complete TOP VIEWFRONT VIEWADC P.N. ATM-AC-CON orPHOENIX CONTACT P.N. 1777992L NPlug Retention ScrewsPowerConnectionL

If your locomotives and cars use more then 2.5 Amps, it is necessary to split the layout in several power sections and feed each section with an extra "booster" which provides more amperage. Terminals C & D on your Commander can be used to wire in extra boosters. For more information about adding power stations to your layout, please see the DCC section of Atlas' web site at LIMITED ONE-YEAR WARRANTY Atlas Model Railroad Company, Inc. warrants that this Commander will be free from defects in mat

Features • Turns on lighting when motion is detected. • Automatically turns lighting off. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). This package includes: Bulb Holders Rubber Plug Plastic Hanger Cover Plate Sensor 2 Wire Connectors Mounting Bolt Mounting Strap Gasket 6 Screws (3 sizes included) Light Control Requirements • The light control requires 120-volts AC. • If you want to use Manual Mode, the control must be wired through

. Walk through the coverage Ball area noting where you are Joint when the lights turn on. Move the sensor head up, down, or sideways to change the coverage area. Keep the sensor at least 1" (2.5 cm) away from the lamps. . Adjust the RANGE as needed. RANGE set too high may increase false triggering. . Secure the sensor head by tightening the clamp screw. Do not overtighten the screw. . Set the amount of ON-TIME you want the lights to stay on Aim Sensor Down for Short Coverage Aim Sensor Higher fo

Flip the light switch off for one second then back on to toggle between AUTO and MANUAL MODE. Manual mode works only with the ON-TIME switch in the 1, 5, or 10 position. 240-026-A © 2008 Atlas Lighting Products, Inc. 598-1092-02 Mode Switching Summary TEST Move ON-TIME Switch to 1, 5, or 10 minutes AUTO Flip light switch off for one second then back on* MANUAL MODE * If you get confused while switching modes, turn the power off for one minute, then back on. After the calibration time the control

Junction Box Lamp Holders . Turn power off at the fuse or circuit breaker. . Remove the existing light fixture, if present. 598-1096-01 -2 TEST AND ADJUSTMENT . Turn on the circuit breaker and light switch. NOTE: Sensor has a 1 1/2 minute calibration period before it will detect motion. When first turned on, wait 1 1/2 minutes. . Turn the RANGE control to the mid position and the ON-TIME control to the TEST position. ON-TIME RANGE 10 5 1 TEST MIN MAX Bottom of Sensor Avoid aiming the control at: