Votes - 0, Average rating: 0
(
)
)
|
Other manuals for this model:
manual abstract
OLD occurs when performing a delete operation with the olrad command, or with the Systems
Management Homepage (SMH) on systems with this OLD feature.
A dynamic module unload can occur with kcmodule, swinstall, or swremove commands.
If the CRA fails in this way during a swinstall or swremove operation, the system will
automatically reboot to complete the requested operation. If the CRA fails during a kcmodule
fcd=unused operation, the unload action will not occur until the system is manually rebooted.
Corrective action: Install patch PHCO_36356 to fix this problem. This patch is delivered in
the HWEnable11i patch bundle on the HP-UX 11i v3 (B.11.31) OEUR media for December
2007. You may also check availability of the patch at the HP IT Resource Center site: http://
itresourcecenter.hp.com
•
Update to Software Distributor is required
If the updated or patched Software Distributor is not in place, a necessary reboot might not
be performed during installation of the I/O drivers with DLKM functionality, which includes
the FibrChanl-01 product.
Corrective action: On systems prior to the HP-UX 11i v3 December 2007 OEUR, you must
install Software Distributor patch PHCO_36530, or install the B.11.31.0709.308 or later
revision of the Software Distributor product from http://docs.hp.com/en/SD
•
EFI SEARCH causes boot to fail on rx7640, rx8640, and sx2000 Superdome server systems
Running the SEARCH command at the EFI shell on rx7640, rx8640, and HP Integrity
Superdome/SX2000 server systems can cause the system to fail to boot through a Fibre
Channel HBA. rx7640 systems have a built-in SEARCH of slot 7. Affected 2Gb Fibre Channel
HBAs are: A6826A, A9782A, A9784A, and AB465A with EFI driver version 1.47 or earlier.
Affected 4Gb Fibre Channel HBAs are: AB378A and AB379A with EFI driver version 1.01.
The boot will fail with a message similar to the following:
Load of HP-UX Primary Boot: 1.0.1/1/0/4/0.8.0.255.0.6.0
failed: Not Found
Corrective action: A fix in the 2Gb/4Gb drivers has been released. The following steps will
resolve the issue:
1.
Go to www.hp.com
2.
Click Software & Driver Downloads.
3.
In the white text box, type the name of the I/O card, such as A6826A.
4.
Click the >> button.
5.
Click the Cross Operating System button.
6.
Look for EFI 1.49 or later for adapters A6826A, A9782A, A9784A, and AB465A. Look
for EFI 1.05 or later for adapters AB378A and AB379A.
•
Configuring an alternate path on the same 2–Port HBA as the primary path
On midrange and high end Integrity servers, if the primary and alternate boot devices are on
the same Fibre Channel HBA port, an attempt to manually boot from the alternate device will
fail.
For example, if your primary and alternate paths are set as follows:
Primary bootpath: 0/0/10/1/0/4/0.8.0.255.0.7.0
Alternate bootpath: 0/0/10/1/0/4/0.8.0.255.0.0.0
This will set the primary and alternate bootpaths, but you will only be able to boot from the
primary path.
Corrective action:The issue can be resolved by following one of the following scenarios:
8
...Other models in this manual:
Network Equipment - HP-UX 11i v3 I/O Cards (264.62 kb)