STARTING A WARM ENGINE Pull starter rope sharply while squeezing throttle trigger until engine runs. NOTE: Normally, the warm starting procedure can be used within 5- --10 minutes after the unit is turned off. If the unit sits for more than 10 minutes without being ran, it will be necessary to start the unit by following the steps under STARTING A COLD ENGINE or following the starting instruction steps shown on the unit. STARTING A FLOODED ENGINE Move the start lever to the RUN position and full

Wearing safety leg guards is recommended. S Always wear foot protection. Do not go barefoot or wear sandals. S Secure hair above shoulder length. Secure or remove loose clothing and jewelry or clothing with loosely hanging ties, straps, tassels, etc. They can be caught in moving parts. S Being fully covered also helps protect you from debris and pieces of toxic plants thrown by spinning line/blade. S Stay Alert. Do not operate unit when you are tired, ill, upset or under influence of alcohol, 4

Allowing such contact can result in serious injury. IMPORTANT POINTS S Work slowly, keeping both hands firmly gripped on the pruner. Maintain secure footing and balance. S Plan cut carefully. Check direction branch will fall. S Watch out for springpoles. Springpoles are small size limbs which can catch the chain and whip toward you or pull you off balance. Use extreme caution when cutting small size limbs or slender material. S Watch out for branches immediately behind the branch being pruned. I

2. Check chain for proper tension. Adjust chain tension if necessary. See CHECK CHAIN TENSION section. 3. Sharpen cutters. S To sharpen the cutters, position the file holder level (90°) so that it rests on the top edges of the cutter and depth gauge. NOTE: The chain has both left and right hand cutters. 11 DepthGaugeFileFileHolderCutter90° DepthGaugeFileFileHolderCutter90° 4. Check and lower depth gauges. DepthGaugeToolDepthGaugeFile S Align the 30. file holder marks parallel with the bar and to

Veuilleznepasretournerleproduitaudetaillant. 1--800--554--6723Pleasedonotreturnproducttoretailer. Porfavor,nodevuelvaelproductoallugardecompra. Veuilleznepasretournerleproduitaudetaillant. 1--800--554--6723 Register your product online at: Registre su producto en linea en: Enregistrez votre produit en ligne a l’adresse : Instruction Manual Manual de Instrucciones Manuel d’Instructions PP5500P WARNING: Read and follow all Safety Rules and Operating Instructions before using this product. Failure

S Cut from your left to your right. Cutting on the right side of the shield will throw debris away from the operator. S Always use the handlebar and a properly adjusted shoulder strap with blade (see ASSEMBLY instructions in brushcutter attachment instruction manual). CULTIVATOR SAFETY WARNING: Rotating tines can cause serious injury. Keep away from rotating tines. Stop the engine and disconnect the spark plug before unclogging tines or making repairs. WARNING: Inspect the area to be cultivated

ASSEMBLY INFORMATION - -TRIMMER HEAD TRIMMER HEAD NOTE: Remove the blade and metal shield before attaching the plastic shield and trimmer head. To remove blade, align hole in the dust cup with the hole in the side of the gearbox by rotating the blade. Insert a small screwdriver into aligned holes. This will keep the shaft from turning while loosening the blade nut. Remove blade nut by turning clockwise. Remove the screwdriver. Remove both washers and blade. To remove metal shield, loosen and rem

Disconnect spark plug wire. Drain gasoline from fuel tank. AROUND THE YARD » Tip depth stake forward until it is held by the stake spring. Push tiller handles down, raising tines off the ground. ® Push or pull tiller to desired location. AROUND TOWN Disconnect spark plug wire. ® Drain fuel tank. • Transport in upright position to prevent oil leakage. BEFORE STARTING ENGINE IMPORTANT: BE VERY CAREFUL NOT TO ALLOW DIRT TO ENTER THE ENGINE WHEN CHECKING OR ADDING OIL OR FUEL. USE CLEAN OIL

#10-24 17 102604X Grip, Bar Control 4 126949X428 Bracket, Handle 18 150696 Bolt, Pivot 5 72110514 Bolt, Carriage 5/16-18x1-3/4 21 145829 Bar, Controi 6 108281X Rod, Shift 22 150744 Grip, Handle 7 72110608 Bolt, Carriage 3/8-16 x 1 Gr. 5 24 73731000 Nut, Keps #10-24 UNC 8 4497H Clip, Hairpin 25 127012X Control, Throttle 9 109229X Lock, Handle 26 146480 Grommet, Handle 10 73930600 Nut 3/8-16 27 10040500 Washer, Lock 5/16 11 19131611 Washer 13/32x1 x 11 Ga. 28 73800500 Locknut 5/16-18 12 1

Pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). • Pull recoil starter handle quickly. Do not let starter handle snap back against starter. Repeat if necessary in half choked position. • When engine starts, slowly move choke controi to “RUN” position as engine warms up. NOTE: A warm engine requires less choking to start. • Move throttle control to desired running position. Allow engine to warm up for a few minutes before en