3. If the engine still fails to start or fire, refer to the troubleshooting flow chart at the end of this manual. Stopping the Engine Idle the engine briefly before stopping (about 2 minutes), then slide the ignition switch to the “O” (Engine OFF) position. Checking Unit Condition NEVER operate the unit with the cutting attachment shield or other protective devices removed! Use only authorized Shindaiwa parts and accessories with your Shindaiwa trimmer. Do not make modifications to this unit wit

1. Prime the primer bulb until no more fuel is passing through. 2. Start and run the engine until it stops running. 3. Repeat steps 1 and 2 until the engine will no longer start. ¦ Remove the spark plug and pour about 1/4 ounce of 2-cycle mixing oil into the cylinder through the spark plug hole. Slowly pull the recoil starter 2 or 3 times so oil will evenly coat the interior of the engine. Reinstall the spark plug. ¦ Before storing the unit, repair or replace any worn or damaged parts. ¦ Remove

Align hole in adapter plate with notch in gear housing, and insert Locking Tool (A) to prevent splined shaft from turning. Arrow on gear housing points to notch. Tighten 10 mm nut securely. 4. Insert Cotter Pin (L) in hole in PTO shaft, and bend pin legs around shaft counterclockwise to retain 10 mm nut. IMPORTANT! Never reuse a cotter pin - install a new cotter pin each time a blade is installed or replaced. 5. Remove locking tool. The unit should now be completely assembled and ready for use w

Disconnect the spark plug wire before performing service or maintenance. Muffler This unit must never be operated with a faulty or missing spark arrester or muffler. Make sure the muffler is well secured and in good condition. A worn or damaged muffler is a fire hazard and may also cause hearing loss. Spark Plug Keep the spark plug and wire connections tight and clean. Fasteners Make sure nuts, bolts, and screws (except carburetor adjusting screws) are tight. WARNING! Non-standard accessories, c

NOTE: Every unit is run at the factory and the carburetor is set in compliance with emission regulations. Carburetor adjustments, other than idle speed, must be performed by an authorized Shindaiwa dealer. Adjusting Engine Idle The engine must return to idle speed whenever the throttle lever is released. Idle speed is adjustable, and must be set low enough to permit the engine clutch to disengage the cutting attachment. WARNING! The cutting attachment must NEVER rotate at engine idle! If the idl

3. Inspect the extension power cord for loose or exposed wires and damaged insulation. If damaged, replace before using the appliance. WARNING Do not operate your chain saw in a wet or damp environment. Do not expose the saw to rain, snow or sleet. Moisture will cause short circuits. Replace or repair any damaged or frayed extension cords before using your saw. Keep the cord away from the cutting area and position the cord so that it will not be caught on branches or other objects during cutting

A guard or other part that is damaged should be properly repaired or replaced by an authorized service center, unless otherwise indicated in this instruction manual. 13. RESTER VIGILANT: Attention a ce que vous faites. Utiliser votre sens commun. Ne pas manier la tronconneuse par moments de fatigue. Rester a l’ecart de la chaine quand le moteur est en marche. Avant de mettre le moteur en marche, s’assurer que la chaine ne touche rien. 14. ENTRETENIR LA TRONCONNEUSE AVEC SOIN: Verifier les cordon

• Loosen (do not remove) tine shield nut on underside of tine shield. • Pull belt guard out and away from unit. • Replace belt guard by reversing above procedure. Be sure slot in bottom of belt guard is under head of tine shield bolt and all nuts are tightened securely. CAP NUTS AND WASH ERS BELT GUARD TINE SHIELD NUT Fig. 20 TO REPLACE V-BELTS (See Figs. 21 and 22) Replace V-belts if they have stretched considerably or if they show cracks or frayed edges. There are two (2) V-belts -forward (ins

SAFETY RULES Safe Operation Practices for Walk-Behind Powered Ro ta ry Tillers TRAINING • Read the Owner’s Manual care ful ly. Be thor ough ly fa mil iar with the controls and the proper use of the equip ment. Know how to stop the unit and disengage the controls quickly. • Never allow children to operate the equipment. Never allow adults to op er ate the equipment without proper instruction. • Keep the area of operation clear of all persons, par- tic u lar ly small children, and pets. PREPARATIO