SRM-230 S/N: S80613001001 - S80613999999 Engine Cover, Exhaust Cover.........................................................................................................................................4 Fuel System.....................................................................................................................................................................6 Starter -- Standard................................................................................................

15M (50 ft.) 8 DESCRIPTION The ECHO product you purchased has been factory pre-assembled for your convenience. Due to packaging restrictions some assembly is required. After opening the carton, check for damage. Immediately notify your retailer or ECHO Dealer of damaged or missing parts. Use the contents list to check for missing parts. EMISSION CONTROL IMPORTANT ENGINE INFORMATION ENGINE FAMILY : TEH021UB24RA Type 1E Models DISPLACEMENT : 21.2cc THIS ENGINE MEETS U.S. EPA PHI AND 1995 - 1999 CA

ALWAYS fill fuel tanks outdoors over bare ground. • Securely tighten fuel cap after refueling. • Inspect for fuel leakage. If fuel leakage is found, do not start or operate unit until leakage is repaired. IMPORTANT Spilled fuel is a leading cause of hydrocarbon emissions. Some states may require the use of automatic fuel shut-off containers to reduce fuel spillage. Contact your ECHO dealer for ordering information. 3 M (10 ft.) After Refueling; • Wipe any spilled fuel from the unit. • Move at le

Wooden carbon scraper. Parts Required: P/N 13001642031 Spark Arrestor Screen P/N 14586642031 Screen Holder 1. Remove screen cover (A), screen holder (B), and gasket (C) from muffler body. 2. Clean carbon deposits from screen (D) and muffler components. 3. Replace screen if it is cracked, plugged or has holes burned through. 4. Install with new gaskets. 20 20 Emission Models Level2. Tools required: Screwdriver, Tachometer (ECHO P/N 99051130017). Parts required: None. NOTE Every unit is run at the

2. Place the stop switch in the "OFF" position. 3. Remove accumulation of grease, oil, dirt and debris from exterior of unit. 4. Perform all periodic lubrication and services that arerequired. 5. Tighten all the screws and nuts. 6. Drain fuel tank completely. Press purge bulb 6 -7 times to remove remaining fuel from carburetor then drain the tank again. Close choke, start and run the engine until it stops due to lack of fuel. 7. A. Allow engine to cool then remove the spark plug and pour7 cc(1/4

FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY. ECHO, INCORPORATED X750-005 26 2 400 Oakwood Road, Lake Zurich, Illinois 60047-1564 Phone : 847-540-8400 X750216-1602 Printed in Japan 0504rd 0419 ES 2 INTRODUCTION The ECHO Trimmer/Brushcutter, model SRM-400U is lightweight, high performance gasoline powered rotary trimmer which is designed for brushcutting, weed control and grass trimming in areas which are difficult to control by any other means. The trimmer is equipped with a safety shoulder h

Se deben leer y entender ambos para llevar a cabo una operacion segura y apropiada. X753001260 X7532093000 11/03 2 2 Bienvenido a la familia ECHO. Este producto ECHO ha sido disenado y fabricado para proporcionar una larga duracion y seguridad en el trabajo. Lea y entienda este manual y el MANUAL DE SEGURIDAD incluido en el mismo paquete. Vera que es facil de usar y esta lleno de recomendaciones de operacion utiles y mensajes de SEGURIDAD. EL MANUAL DEL OPERADOR Lea antes de la operacion y guard

If your unit does not have a clamp, follow these directions. Tools Required: Screwdriver, 8mm x 10mm Open End Wrench. Parts Required: Clamp, 4mm x 18mm Hexagon Head, Bolt, Link. 6. Remove shield and gear housing as an assembly. a. Loosen two (2) screws that clamp the gear housing to the drive shaft housing. b. Remove locating screw found at the top of the gear housing. Pull shield and gear housing assembly from the drive shaft assembly. IMPORTANT Prevent flexible drive cable from sliding f

Secure with two (2) 6mm x 30mm bolts. 9. Install hook. Three loop hook included with Blade Conversion Kit for blade use. Position 8 5/8 inch (220mm) from engine end of drive shaft assembly. DO NOT tighten at this time. 10. Install handles in bracket (G), place clamp top over handles and securewithfour(4)5mmx35mmbolts(H). 400 mm (15*3/4 In.) 220 mm (8-21/32 In.) ENGINE END 1SMEEHO. 11. Secure throttle cable and leads to drive shaft by sliding wedge under harness hook. 12. Install power h

Tighten and/or replace as needed. • Inspect shield for damage and make sure it is securely in place. Replace if shield is damaged or missing. • Check that the cutting attachment is firmly attached and in safe operating condition. IMPORTANT 80-Tooth blade requires professional sharpening. NOTE ECHO, INC. will not be responsible for the failure of cutting devices, attachments or accessories which have not been tested and approved by ECHO. WARNING Moving parts can amputate fingers or cause severe i