Compliance of this drive, as a system component, was confirmed with a test system. We cannot guarantee that your system will comply. The drive is not meant for external use (without properly designed enclosure, shielded I/O cable, etc.). Sicherheitsanleitung 1. Das Gerrat ist ein Einbaugerat, das fur eine maximale Umgebungstempeatur von 60°C vorgesehen ist. 2. Zur Befestigung des Lufwerks werden 4 Schrauben 6-32 UNC-2A benotigt. Bei seitlicher Befestigung darf die maximale Lange der Schrauben im

Some legacy BIOS cause hangs on startup or other problems if it is not ATA/100 compatible. For more information, see the earlier section on the Ultra ATA/100 requirements. In addition, some legacy BIOS may cause a hang due to the large drive capacity. Consider using the alternate capacity jumper if it is available on your drive model. Use the alternate capacity jumper if your computer does not support higher capacity drives. The jumper will limit large capacity drives to 32 Gbytes. Note. If thes

If using a 40-pin 80-conductor cable, attach the blue connector to the motherboard, the black connector to the master drive and the grey connector to the slave. Caution. Align pin 1 on the motherboard connector with pin 1 on your drive connector. Pin 1 is marked by a stripe on one side of the cable. 2. Secure the drive using four 6-32 UNC mounting screws in either the side- mounting or bottom-mounting holes. Insert the screws no more than 0.20 inches (5.08 mm) into the bottom-mounting holes and

Do not drop or jar the drive. Handle the drive only by the edges or frame. • Drive electronics are extremely sensitive to static electricity. While installing the drive, wear a wrist strap and cable connected to ground. • Turn off the power to the host system during installation. • Do not disassemble the drive; doing so voids the warranty. Return the entire drive for depot service if any part is defective. • Do not apply pressure or attach labels to the drive. Setting the jumpers Refer to the ju

You can get this free disc drive installation software from our web site at or run the program directly from your web browser. In either case, you should run DiscWizard before you install your drive. To run DiscWizard: Follow the instructions on the download page at to create a diskette and complete the installation. If you cannot run DiscWizard, follow the instructions on this installation sheet to install and configure your drive. What you need • A Phillips screwdriver and four 6-32 UNC drive

To determine the warranty status of your Seagate disc drive, contact your place of purchase or visit our web site at for more information. Return Merchandise Authorization (RMA). Run SeaTools to diagnose your drive before requesting a return authorization. In addition, please verify that your drive is defective by following the troubleshooting checklist in this guide. Seagate offers comprehensive customer support for all Seagate drives worldwide. Seagate customer service centers are the only fac

Preparing the drive using DiscWizard Installing a single drive If you are installing a single drive, we recommend using DiscWizard to automatically partition and format your drive. DiscWizard software is available at and is free. During the download, the Diskette Creator creates a portable bootable diskette. To run DiscWizard: 1. Insert your bootable DiscWizard diskette and follow the instructions. DiscWizard will guide you through the installation process. 2. Boot your computer from the Windows

• Cable select: Computers that use cable select to determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interOptions jumper block face bus. To enable cable select, set a jumper on pins 5 and 6. • Alternate capacity jumper: Drives with a 40-Gbyte capacity or greater are limited to 32 Gbytes. Use this jumper only if you have a legacy system with a BIOS that does not support large capacity disc drives. When using the alternate capacity jumper, • Manager software is

2. Does the computer recognize the drive? Verify that the drive is enabled in the system CMOS or setup program. If not, select the autodetect option and enable it. If your drive has a problem, it may not be recognized by the system. 3. Does FDISK detect the drive? Run the FDISK program located on your Windows startup diskette. Type fdisk/status to verify that your hard drive is present and recognized by the system. 4. Does Scandisk find the drive defect-free? Scandisk is a utility located on you

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Medalist 1080sl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SCSI Interface Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Contents Introduction .. .. .. .. .. .. .. .. .. .. .. .. . 1