Login:
Votes - 5, Average rating: 4.2 ( )

User manual Seagate, model BARRACUDA 7200.7 ST3120026A

Manafacture: Seagate
File size: 116.08 kb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


• Cable select: Computers that use cable select to determine the master and slave drives by selecting or deselecting pin 28, CSEL, on the interOptions jumper block face bus. To enable cable select, set a jumper on pins 5 and 6. • Alternate capacity jumper: Drives with a 40-Gbyte capacity or greater are limited to 32 Gbytes. Use this jumper only if you have a legacy system with a BIOS that does not support large capacity disc drives. When using the alternate capacity jumper, • Manager software is required to achieve the drive’s full capacity. 268 4 1753 Drive is slave *Master or single drive *Cable select Master with non ATA- compatible slave Alternate capacity. Limits drive capacity to 32 Gbytes Attaching cables and mounting the drive 1. Attach one end of the drive interface cable to the interface connector on your computer’s motherboard (see your computer manual for connector locations). Master Pin 1 Slave Note. When configuring two ATA devices on the same cable, both must use Cable Select or both must use Master/Slave jumper settings. If using a standard 40-pin cable, the master and slave drives can be placed in any position. If using a 40-pin 80-conductor cable, attach the blue connector to the motherboard, the black connector to the master drive and the grey connector to the slave. Caution. Align pin 1 on the motherboard connector with pin 1 on your drive connector. Pin 1 is marked by a stripe on one side of the cable. 2. Secure the drive using four 6-32 UNC mounting screws in either the side- mounting or bottom-mounting holes. Insert the screws no more than 0.20 inches (5.08 mm) into the bottom-mounting holes and no more than 0.14 inches (3.55 mm) into the side-mounting holes. Note. Do not overtighten the screws or use metric screws. This may damage the drive. 3. Attach the interface connector and the power connector to the drive. Configuring the BIOS Close your computer case and restart your computer. your computer may automatically detect your new drive. If your computer does not automatically detect your new drive, follow the steps below. a. Restart your computer. While the computer restarts, run the System Setup program (sometimes called BIOS or CMOS setup). This is usually done by pressing a special key, such as DELETE, ESC, or F1 during the startup process. b. Within the System Setup program, instruct the system to auto detect your new drive. c. Enable LBA and UDMA modes, if available and then save the settings and exit the Setup program. When your computer restarts, it should recognize your new drive. If your system still doesn’t recognize your new drive, see the troubleshooting section on the back of this sheet. BIOS Settings Drive Model Formatted Gbytes Total Sectors* Cache ST3200822A 200.0 390,721,968 8 Mbytes ST3200821A 200.0 390,721,968 2 Mbytes ST3160023A 160.0 312,581,808 8 Mbytes ST3160021A 160.0 312,581,808 2 Mbytes ST3120026A 120.0 234,441,648 8 Mbytes ST3120022A 120.0 234,441,648 2 Mbytes ST380013A 80.0 156,301,488 8 Mbytes...

Other models in this manual:
Portable Players - BARRACUDA 7200.7 ST3120022A (116.08 kb)
Portable Players - BARRACUDA 7200.7 ST3160021A (116.08 kb)
Portable Players - BARRACUDA 7200.7 ST3160023A (116.08 kb)
Portable Players - BARRACUDA 7200.7 ST3200821A (116.08 kb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category