• Adhere to all warnings and security advices, and retain this document for future referenceE aa Install the unit in accordance with the provided instructions P er Supply: O The unit should be connected to a power supply outlet only of the voltage and frequency marked on its rear panel and/or its AC adapterE O The power supply cord should be routed so that it is not likely to be walked on or pinchedE O The power supply cord of the unit should be unplugged from the wall outlet when it is to be un

(TERMINATED UNUSED INPUTS) MIC EQ HI ±10 +/- 2dB AT 10KHz LOW ±10 +/- 2dB AT 100Hz CHANNEL EQ HI 9 +/- 2dB AT 13KHz -15 +/- 3dB AT 13KHz MID 9 +/- 2dB AT 1KHz LESS THAN -23dB AT 1KHz LOW 9 +/- 2dB AT 70Hz -26 +/- 3dB AT 70Hz POWER SOURCE AC 9V,1000mA DIMENSIONS 230 (W) X 267 (D) X 111 (H) mm WEIGHT 1.65Kgs CONNECTIONS 1) Connect the power cord to an AC outlet. 2) Connect the RCA cable to the PHONO input of your mixer. You can also use a line input by setting the phono/line switch at the rear of

. . 5 1. Channel Gain - Adjusts the pre-fader volume for cleaner sound. Reduce the channel gain if you notice the level indicators flashing red. 2. Mic Input Gain - Adjusts microphone input level. 3. Mic EQ - The mic channel includes a two-band EQ with a range of +10 dB to -10 dB. 4. Channel EQ - Adjusts the high, mid and low frequency levels of the input channels for either making the treble or bass louder or to be used as an effect. 5. Input Fader - Controls individual source levels (channels)

The appliance has been exposed to rain; or D. The appliance does not appear to operate normally or exhibits a marked change in performance; or E. The appliance has been dropped, or the enclosure damaged. CAUTION: To reduce the risk of electric shock, do not remove any cover. No user-serviceable parts inside. Refer servicing to qualified service personnel only. The lightning flash with arrowhead symbol within the equilateral triangle is intended to alert the user to the presence of un-insulated “

• Adhere to all warnings and security advices, and retain this document for future reference. Installation: Install the unit in accordance with the provided instructions Power Supply: • The unit should be connected to a power supply outlet only of the voltage and frequency marked on its rear panel. • The power supply cord should be routed so that it is not likely to be walked on or pinched. • The power supply cord of the unit should be unplugged from the wall outlet when it is to be unused for a

Up to 32 steps can be stored in this sequence. The recorded sequence can start playing by pressing the PLAY button. Or it can start automatically after you stop recording by turning on the AUTOSTART mode. To turn AUTOSTART on or off: press and hold the MODE button in the SAMPLER SEQUENCER section and turn the left FX TIME encoder. The display will change between ASTRT ON and ASTRT OFF. 35. REVERSE BUTTON – When engaged (illuminated) playback will occur in the opposite direction (backwards). This

UNIT OVERVIEW......................................................................................................................13 DECK A (LEFT SIDE) ...............................................................................................................13 DECK B (RIGHT SIDE) .............................................................................................................13 DECK CONTROLS .......................................................................................

Crossfader Reverse -The crossfader reverse changes the direction of the fade on the crossfader (23). FRONT PANEL FRONT PANEL 25. Crossfader Curve -Controls the taper (fade) shape of the crossfader (23). The crossfader curve control continually adjusts the curve from a sharp cut to a long fade. 26. Headphone Outputs -1/4” and 1/8” connector jacks for headphones. BACK PANEL BACK PANEL Power -Power switch to turn the mixer “ON” or “OFF”. AC IN: This is the input connection for the included power su

Connect the power cord to the auxiliary power outlet on the rear panel of your amplifier or receiver or to a household AC outlet. 2. Connect the unit output terminals to the PHONO jack of your amplifier or receiver. Output terminals Amplifier (Receiver) L White) L Channel R (Red) R Channel GND (Spade) GND NOTE: Be sure to connect the ground terminal firmly to the amplifier or receiver. If this connection is not made or is loose, a power source "HUM" will result. The major cause of problems in so

• You can connect the REC output directly to the input of a CD or cassette recorder or to a mixing board to record your set. GETTING STARTED GETTING STARTED • Once your system is set up, make sure the MASTER (28) is turned all the way down. • Turn on the mixer and check your levels. Start with the channel faders (16) down, GAIN (11) and EQs (12) at 12 o’clock. Start the music. Adjust the GAIN until the LED indicator is blinking. You can also use the main LED meter to view the input level of each