You can send another command after you receive the . i.e. send: *01X01 response: 01X01 Note: Only for reading (X01 command). 01 is address. Frequency mode: response time is controlled by the gate time. If gate time is increased then response time is longer. Other modes: response time is not controlled by the gate time. WARM UP TO RATED ACCURACY: 30 minutes INPUT POWER: 10 to 32 Volt DC POWER CONSUMPTION: 3 Watts (125mA at 24V DC) OPERATING AMBIENT: -5 to +55 °C STORAGE TEMPERATURE:

Box 4047 ISO 9001 Certified Stamford CT 06907-0047 TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1 TEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.ca For immediate technical or application assistance: USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA® Customer Service: 1-800-622-2378 / 1-800-622-BEST® Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN® TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA Mexico: TEL: (00

You can send another command after you receive the . i.e. send: *01X01 response: 01X01 Note: 01 is address. WARM UP TO RATED ACCURACY: 30 minutes INPUT POWER: 10 to 32 Volt DC POWER CONSUMPTION: 2.4 Watts (100 mA at 24 V DC) OPERATING AMBIENT: -5 to +55 °C STORAGE TEMPERATURE: -40 to +85 °C RELATIVE HUMIDITY: 90% at 40 °C non-condensing RETURN 5A 1A 100mA + - N/C SIGNAL INPUT DC PWR 1 2 { Page 20 DRX-ACV SPECIFICATIONS INPUT RANGES: 400 mV, 4V, 40 Volt, 400 Volt FREQUENCY RANGE: 30

OMEGA Warranty adds an additional one (1) month grace period to the normal one (1) year product warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product. If the unit should malfunction, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective it will be

Install Jumper onto S1-A on Component Side of Board. Version A Version B Testpoint/Jumper Locations Page 5 IV. COMMANDS FOR ACCESSING EEPROM: NO. command letter index meaning # of bytes 1. R,W 01 Input range or function 1 2. R,W 02 Input/output Configuration 1 3. R,W 03 Decimal point 1 4. R,W 04 Filter time constant 1 5. R,W 05 Reading scale 3 6. R,W 06 Reading offset 3 7. R,W 07 Communication parameters 1 8. R,W 08 Communication bus format 1 9. R,W 09 Communication Data format 1 10. R,W 0A Comm

COMMUNICATION PARAMETERS: This is one byte data and specifies BAUD, PARITY, DATA, and STOP bit. BAUD = bits 2,1,0 are: 000-001 not used 010 for 1200 011 for 2400 100 for 4800 101 for 9600 110 for 19200 111 not used Page 12 PARITY = bits 4,3 and are: 00 for NO 01 for ODD 10 for EVEN 11 not used DATA BIT = bit 5 and is: 0 for 7 data 1 for 8 data STOP BIT = bit 6 and is: 0 for 1 stop 1 for 2 stop Bit 7 : always 0 Note 1: Stop bit is always 1. Unless 7 data, no parity is selected then unit will use

To use the RS485 communication for the Signal Conditioners you’ll need an available Communication port in your computer and have access to a generic communication software program (e.g.: Procomm1, Windows2 HyperTerminal3, etc, see details below for information). A RS485 signal conditioner communication software program is also available as an option to speed the set-up. A RS232 to RS485 converter box will also be required if your computer communications port is RS232. 1 Procomm is a registered t

Do not forget to include your name, address and a daytime telephone number. Alternatively, you can contact our freephone service hot-line on the number given below. Office hours are as follows: Mon - Fri: 8 am - 6 pm, Sat: 10 am - 2 pm, Sun: 10 am - 4 pm UK / NORTHERN IRELAND HELPLINE: 0870 7323023 REPUBLIC OF IRELAND HELPLINE: 1800 481005 WEB SUPPORT: Omega, Interex House, Prospect Close, Lowmoor Business Park NG17 7LF Kirkby In Ashfield, England Replacements or repairs under guarantee regulati

• If required, the plunge depth can be set accurately to within 0.1 mm. • Retighten button 9. Adjustment using the revolver- depth stop The revolver-depth stop enables you to quickly choose between six different cutting depths. These are also determined by the adjustment of the depth stop (10). • Adjust the required cutting depth by rotating the revolver-depth stop (21). Helpline No. UK / Northern Ireland 0870 7323023 • Rep. Ireland 1800 481005 Web Support: Model Number: PBF-1200 15 Helpline No.

6.2.1 Pumping in the FLOW RATE Mode To pump fluid in the FLOW RATE Mode, do the following: 1. Set up the pump motor for pumping, according to Chapter 3. 2. Toggle the ON/OFF switch to turn on the unit’s power. The display is in the STOPPED Display Mode. Refer to Figure 6-3. 3. Either set the TUBE ID for the tube you are using (following Section 5.3) or calibrate the tube (following Section 5.5), before continuing. 4. Press the FLOW RATE key. FLOW RATE Display shows xxx mL/min ACTION Displays cur