Login:
Sorted: Name ↑   Downloads   Rate   Size ↑  

Directed Audio XTR Amplifier XTR5004

downloaded: 2File size: 1 mb    Manafacture: Directed Audio  
Category: Car Amplifiers

All rights reserved. 13 NOTE: Make sure all the equipment in the system is turned off when making or breaking connections to the input RCA’s or speaker terminals. Turn on the system and slowly turn up the volume control only after double checking all wire connections. Power for systems with a single amplifier can be supplied by most automotive electrical systems. Systems with multiple amplifiers may require a higher capacity battery, alternator or the use of a storage capacitor. We strongly reco

Directed Audio XTR Amplifier XTR2504

downloaded: 14File size: 1 mb    Manafacture: Directed Audio  
Category: Car Amplifiers

(70 Watts at 2.) per channel, four- channel amplifier with dual built-in high-pass and low-pass 12dB/ octave crossover and Bass Boost the XtR2504 is capable of 6, 5, 4, 3 or 2 channel operation with a maximum power capability of 250 Watts into two 4. bridged loads l XTR5004 -80 Watts at 4. (125 Watts at 2.) per channel, four- channel amplifier with dual built-in high-pass and low-pass 12dB/ octave crossover and Bass Boost the XtR5004 is capable of 6, 5, 4, 3 or 2 channel operation with a maximum

Directed Audio XTR5002

downloaded: 8File size: 979 kb    Manafacture: Directed Audio  
Category: Car Amplifiers

All rights reserved. Sealed Example High-Pass Set at 30Hz In this example, the frequency has been increased to 30 Hz Up to 6 dB of boost is capable at this frequency With +6dB of boost, the woofer has more output down to 23 Hz the overall usable output is increased Figure 8 Figura 8 Abbildung 8 Figure 9 Figura 9 Abbildung 9 AMPLIFIeR WIRInG Power Connections • Power connections accept up to 4 AWG wire • 4 AWG power and ground wire recommended for optimal performance • Connect 12V+ to the battery

Directed Audio XTR2502

downloaded: 19File size: 979 kb    Manafacture: Directed Audio  
Category: Car Amplifiers

AmplifierMODELXTR2502XTR5002OWNER'S MANUAL AmplifierMODELXTR2502XTR5002OWNER'S MANUAL Contents english 1 Francais 19 espanol 35 Deutsch 51 Italiano 67 Portugues 83 Introduction 2 What’s in the Box 2 Practice safe sound™ 2 end Panel Layouts 3 CeA specifications 4 specifications 5 Amplifier settings 6 signal Input and output Configurations 6 Input Gain 6 Line output Configurations 6 Internal Crossover Configurations, Flat (full range) 6 Crossover switch 6 Low-Pass Crossover 6 High-Pass Crossover 7

Directed Audio 4600X

downloaded: 3File size: 747 kb    Manafacture: Directed Audio  
Category: Car Audio

For mid-bass/midrange settings, try to keep the setting low enough to keep your sound stage in front of you, without overdriving the speaker. It will be to your advantage to spend some extra time with this adjustment, listening to familiar music or system set-up discs to achieve the kind of musical reproduction that you prefer. • The gain adjustment allows you to set proper signal match for clean, quiet amplifier operation. For full-range and simultaneous stereo/mono bass applications, start by

Directed Audio 2300X

downloaded: 6File size: 747 kb    Manafacture: Directed Audio  
Category: Car Audio

10. Due to the high-frequency MOSFET switching power supply, filtering the power cable is not generally required (remember that the amp can’t deliver full output if the power supply is restricted). Proper grounding of the signal source is mandatory for the amplifier to reach its performance peak. If the RCA inputs are not grounded adequately via the signal source, electrical noise from the vehicle may be picked up in the system. © 2003 Directed Electronics, Inc FRONT PANEL CONNECTIONS/CONTROLS N

Directed Audio 1500X

downloaded: 16File size: 747 kb    Manafacture: Directed Audio  
Category: Car Audio

3. Check for any hazards or obstructions such as gas tanks, fuel or brake lines, and wiring harnesses before mounting the amplifier. They may also impair a driver’s ability to hear traffic sounds or emergency vehicles. Use common sense and practice safe listening habits when listening to or adjusting your audio system. 4. Pick a mounting location that will provide adequate access and ventilation and protect the amplifier from heat, moisture, and dirt. 5. Avoid sharp metal areas when routing cabl

Directed Audio 1200T

downloaded: 21File size: 608 kb    Manafacture: Directed Audio  
Category: CD Players

• The gain adjustment allows you to set proper signal match for clean, quiet amplifier operation. For full-range and simultaneous stereo/mono bass applications, start by playing some music you are familiar with. With the gain adjustment on the amplifier in the middle of its rotation, bring up the volume on your head unit to the 3/4 volume setting or until you start to hear distortion or clipping. If you hear distortion before you reach the 3/4 volume setting of your head unit, reduce the gain se

Directed Audio D1200

downloaded: 2File size: 494 kb    Manafacture: Directed Audio  
Category: Car Amplifiers

© 2005 Directed Electronics, Inc. all rights reserved PARALLEL SYNCED GAIN CONNECTIONS/SETTINGS Refer to figure 5 for wiring details. 1. I IIn nnp ppu uut tt S SSi iig ggn nna aal ll - Connect these RCA jacks as described in the Front Panel Connectionsection of this guide. 2. S SSl lla aav vve ee/ //M MMa aas sst tte eer rr S SSw wwi iit ttc cch hh • Set the slave/master switch on the master amplifier to the MASTER position. • Set the slave/master switch on the slave amplifier to the SLAVE posit

Directed Audio D2400

downloaded: 0File size: 494 kb    Manafacture: Directed Audio  
Category: Car Amplifiers

8. T TTo oop pp L LLi iig ggh hht tt O OOp ppt tti iio oon nns ss - -i. Light On W/Service Code ii. Light Off W/O Service Code iii. Light On, W/O Service Code iv. Light Off, W/Service Code Default is Light On, W/O Service Code The amplifier contains the ability to control the lights on top of the unit behind the logo badge. In addition to custom tailoring many other features, your Directed Dealer can use a Bitwriter® (V2.0 or later) to setup the top light so that it is either on or off when the





Category