Login:
Sorted: Name ↑   Downloads   Rate   Size ↓  

Heath Zenith 595-5684-08

downloaded: 6File size: 96 kb    Manafacture: Heath Zenith  
Category: Doors and Windows

• Ding-Dong (two note tune) Push Button: Remove jumper from location 8. Chime: Remove jumper from location 8. • Westminster (Eight note tune) (Available on selected chimes) Push Button: Remove jumper from location 8. Chime: Add a jumper to location 8. Note:All modelshave bothfrontandbackdoortunecapabilities.Werecommend the back door use the Ding tune and the front door use the Ding-Dong tune (or Westminster tune, available on selected chimes). Models that include two push buttons will come facto

Heath Zenith Single Entrance Chime 23/M

downloaded: 0File size: 101 kb    Manafacture: Heath Zenith  
Category: Doors and Windows

Sound travels farthest with the fewest obstacles. Do not place over heat source; i.e., radiator, heater, or stove. At the chosen location drill two small pilot holes 3 1/4" apart in the vertical plane. The chime cover is a push fit onto the base. Remove chime cover to expose base. Position base and mount in place using screws supplied, key-hole shaped slot at the 1 32 Base Plate Chime Cover top (see Figure 1). Figure 1 WIRING THE CHIME To Push Button A. Battery Operation. Do not use with lighted

Heath Zenith 3087590 (AC-6197)

downloaded: 1File size: 115 kb    Manafacture: Heath Zenith  
Category: Doors and Windows

No Service Parts Available for this Product Regulatory Information This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The user is cautioned that changes or modifications not expressly approved by the party responsible for regulatory compliance

Heath Zenith 3035698 (AC-6190)

downloaded: 0File size: 115 kb    Manafacture: Heath Zenith  
Category: Doors and Windows

• Battery powered push button -No wires to run. • 128selectablecodesallowmorethanonechime system in the same house. © 2007 598-1077-02 Use either screws or double sided tape to mount push button. To mount with screws, remove back of case by pushing in tab on bottom with a small screwdriver. Attach back of case to door jamb or wall. Snap front of push button on. When attaching push button using double sided tape, make sure the surface of the door jamb or wall is clean. 1. Install alkaline type A2

Heath Zenith SL-6166

downloaded: 4File size: 115 kb    Manafacture: Heath Zenith  
Category: Doors and Windows

If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. 2. Plug-in the doorbell chime. Chime Volume Control 1. Set the chime volume on the back of the plug-in chime, if desired. 3. Before mounting, test the doorbell range. Plug-in the chime where you want to mount it and temporarily place the doorbell button on the doorjamb. Press the doorbell button. Access Door Ope

Heath Zenith SL-6167

downloaded: 1File size: 115 kb    Manafacture: Heath Zenith  
Category: Doors and Windows

If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. 2. Plug-in the doorbell chime. Chime Volume Control 1. Set the chime volume on the back of the plug-in chime, if desired. 3. Before mounting, test the doorbell range. Plug-in the chime where you want to mount it and temporarily place the doorbell button on the doorjamb. Press the doorbell button. Access Door Ope

Heath Zenith Lighted Wireless Push Button Accessory 598-1227-01

downloaded: 0File size: 116 kb    Manafacture: Heath Zenith  
Category: Doors and Windows

• Battery powered push button - No wires to run. • 128 selectable codes allow more than one chime system in the same house. • LED lighted push bar (see Lighted Push Bar Feature). Lighted Push Bar Feature This ACE® wireless push button contains a LED (Light Emitting Diode) that will illuminate in dark conditions so the push button will be more visible for your guests. This (patent pending) technology and built-in photocontrol will allow the light intensity of the push button LED to increase as th

Heath Zenith SL-5655

downloaded: 0File size: 118 kb    Manafacture: Heath Zenith  
Category: Other Home Accessories

Contact a qualified electrician if there is any question as to the suitability of the system. CAUTION: Make sure the power is off before starting the installation. This fixture can be mounted on a wall with, or without using a flush-mounted junction box. Do not attempt to mount this fixture on a surface-mounted “Wet Location” junction box. Use the instructions below that apply to your application. Installation Using A Junction Box Note: If your junction box protrudes out of the wall slightly, yo

Heath Zenith 3106978 (AC-6196)

downloaded: 4File size: 119 kb    Manafacture: Heath Zenith  
Category: Doors and Windows

(Volume control feature is available on selected chimes). 2.Testrange.Press push button to verify chime and push button work properly. If chime does not sound, see Troubleshooting. WirelessPlug-InChimeAccessoryReceiverModel3106978(AC-6196) This package includes (Style of chime may vary from illustration): • Wireless chime • Hardware pack Chime Volume Control (Depending upon model) Access Door 3.Setchimevolume.Locate control on back of plug-in chime. (Volume control feature is available on select

Heath Zenith 29

downloaded: 2File size: 146 kb    Manafacture: Heath Zenith  
Category: Doors and Windows

• The non-electric chime mounts directly through the door and will accommodate door thicknesses of 3/4" to 2". • The chime is equipped with a viewer. Locating the door chime 1. Mount the chime in the center of the door approximately 4 1/2 feet to 5 feet above the floor. Note: Be sure there are no obstructions on the inside of the door to interfere with the chime’s baseplate. 2. Using the template provided, mark the location of the mounting holes parallel to the edge of the door (see Figure 1). N





Category