|
User manual Heath Zenith, model 29
Manafacture: Heath Zenith File size: 146.04 kb File name: 598-1139-02.pdf
|
|
|
|
Free link for this manual available at the bottom of the page
manual abstract
• The non-electric chime mounts directly through the door and will accommodate door thicknesses of 3/4" to 2". • The chime is equipped with a viewer. Locating the door chime 1. Mount the chime in the center of the door approximately 4 1/2 feet to 5 feet above the floor. Note: Be sure there are no obstructions on the inside of the door to interfere with the chime’s baseplate. 2. Using the template provided, mark the location of the mounting holes parallel to the edge of the door (see Figure 1). Note: It is important that the holes are parallel to the edge of the door for proper operation of the chime. 3. Drill two 1" holes parallel to edge of door. 4. Drill three pilot holes using a 1/16" drill bit. Metal Trim Trim Screw © 2007 HeathCo LLC Two-Note Non-Electric Door Chime – With Viewer Push button assembLy See Figure 1 for push button assembly. Note: If push button assembly is located in an area that is exposed to rain, caulk around the 1” holes before attaching push button to door. attaching Push button assembLy 1. Remove metal trim screw, metal trim, name card holder, and name card from pushbuttonassemblytolocatemounting holes (see Figure 1). 2. Insert viewer and push button shaft into predrilled until push button assembly is flush against door face.Attach using the three mounting screws provided (see Figure 1). 3. Printortypenameandaddressonname card (provided). Place card in holder with printing visible through front of card holder. 4. Place metal trim over push button assembly and name card holder. Secure trim with trim screw (see Figure 1). 1" Viewer Hole 1" Shaft Hole 1/16" Pilot Hole 598-1139-02 Figure 1 - Attaching Push Button Assembly to Door Viewer Push Button Shaft Push Button Assembly Mounting Screw Name Card Name Card Holder Door Edge mounting chime assembLy 1. Position chime assembly over push button shaft and viewer (see Figure 2). 2. Verifychimeassemblyisparalleltoedge of door. 3. Attach the top and bottom of chime assembly securely using mounting screws provided (see Figure 2). oPeration 1. Verify door chime operation by pressing push button. The chime will sound two (2) notes. 2. If door chime does not operate properly, check push button and chime assemblies. Both assemblies must be paralleltothedooredgeforproper chime operation. 3. If necessary, adjust one or both assemblies. Push Button Assembly (Shown on attaching chime cover 1. To insure proper clearance when the cover is attached, break off the excess pushbuttonshaft.IMPORTANT:Toavoid breaking plastic chime assembly parts, use needle-nosed pliers to hold shaft securely while bending shaft back and forth to remove (see Figure 2, View A). 2. Place slot in chime cover over tab on top of chime assembly. 3. Press bottom of chime cover onto chime assembly until cover “snaps” into place. Outside of Door) Chime Assembly Cover Mounting Tab Chime Cover Mounting Screws Break Off Excess Push Button Shaft Cover Mounting Slot Needle-Nosed Pliers view a Figure 2 - Mounting Chime Assembly and Attaching Chime Cover 2 598-1139-02 technicaL service Please call 1-800-858-8501 (english speaking only) for assistance before returning product to store. If you experience a problem, follow this guide. You may also want to visit our Web site at: If the problem persists, call* for assistance at 1-800-858-8501, 7:30 AM to 4:30 PM CST (M-F). You may also write* to: HeathCo LLC P.O. Box 90004, Bowling Green, KY 42102-9004 ATTN: Technical Service * If contacting Technical Service, please have the following information available: Model Number, Date of Purchase, and Place of Purchase. no service Parts available for this Product one year Limited Warranty This is a "Limited Warranty" which gives you specific legal rights. You may also have other rights which vary from state to state or province to province. For a period of one year from the date of purchase, any malfunction caused by factory defective parts or workmanship will be corrected at no charge to you.To obtain a refund or a replacement, return the product to the place of purchase. not covered -Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs and other expendable items are not covered by this warranty. Unauthorized service or modification of the product or of any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for inconvenience, installation, setup time, loss of use, or unauthorized service. This warranty covers only HeathCo LLC assembled products and is not extended to other equipment and components that a customer uses in conjunction with our products. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES. REPAIR OR REPLACEMENT SHALL BE THE SOLE RE...
|