For this reason, it is recommended that the householder consider the use of additional smoke alarms for those areas for increased protection. The additional areas include: basement, bedrooms, dining room, furnace room, utility room and hallways not protected by the requiredsmoke alarms. The installation of smoke alarms in kitchens, attics (finished or unfinished), or garages is notnormally recommended, as these locationsoccasionally experience conditions that can result inimproper operation. Fig

Your Photoelectric alarm is designed to detect the smoke that results from an actual fire. Consequently, it is uncommon for household smoke such as cigarette smoke or normal cooking smoke to cause an alarm. MODEL NO. DESCRIPTION 710LS* ...... 120 VAC Wall Mounted, Provided With a 9 ft. Line Cord, Pulsating Horn 713LS ...... Same as 710LS but with a Temporal Horn * This unit produces a non-temporal audible alarm and is therfore not intended for locations where the desired action of the occupant(s

HoMedics does not authorize anyone, including, but not limited to, Retailers, the subsequent consumer purchaser of the product from a Retailer or remote purchasers, to obligate HoMedics in any way beyond the terms set forth herein. This warranty does not cover damage caused by misuse or abuse; accident; the attachment of any unauthorized accessory; alteration to the product; improper installation; unauthorized repairs or modifications; improper use of electrical/power supply; loss of power; drop

We hope you will find it to be the finest product of its kind. F FFi iir rrs sst tt T TTi iim mme ee S SSe eet ttu uup pp 1. This scale operates on two lithium CR2032 batteries (pre-installed). There is a red strip under the lithium batteries to prevent battery drain in shipping. Remove the red strip before continuing with these instructions. 2. Some models have a static cling label on the lens to prevent scratching. Remove before use. 3. Set the “LB/KG/ST” unit of measure switch located on the

2 3 SC-520.qxd 7/11/06 9:15 AM Page 5 Why Should I Monitor My Body Composition? Typically, total body weight is used to determine if a person is at a healthy weight. A change in weight alone does not tell you whether you have a gain/loss of muscle or fat. In weight management, you want to maintain muscle mass while body fat is lost. How Does This Body Composition Scanner Work? This unit uses BIA (Bioelectrical Impedance Analysis) to measure Body Fat, Body Water, Muscle Mass and Bone Mass. BIA se

Pongase en contacto con HoMedics Customer Service al 1-800-HOMEDICS (1-800-466-3342). Direccion postal: HoMedics Service Center Dept. 168 3000 Pontiac Trail Commerce Township, MI 48390 correo electronico: cservice@homedics.com GARANTIA DE POR VIDA (Valida unicamente en los EE.UU.) HoMedics, Inc., garantiza este producto contra defectos en material y mano de obra mientras este en vida el comprador original a partir de la fecha original de compra con las excepciones que se detallan a continuacion.

This HoMedics product warranty does not cover damage caused by misuse or abuse; accident; the attachment of any unauthorized accessory; alteration to the product; or any other conditions whatsoever that are beyond the control of HoMedics. This warranty is effective only if the product is purchased and operated in the USA. A product that requires modification or adaptation to enable it to operate in any country other than the country for which it was designed, manufactured, approved and/ or autho

Platform 23 Pole Base 5. Use SCREW DRIVER to hook POTHOOK into the hole of the LONG ARM CONNECTION PLATE. 6. Use ALLEN KEY to remove pre-set A SS E M B LY SCREW (located on the bottom of the base) to release the LONG ARM CONNECTION PLAT E into place. AssemblyScrew 7. Use ALLEN KEY to attach POLE to BASE by inserting and turning the 4 SCREWS tightly. Screws 8. Slide POLE COVER down. 9. Replace PLATFORM by sliding it onto BASE and push down until it snaps into place. Pothook Long ArmConnection Pla

The display will turn on, and automatically turn off. The scale is now ready for use. Note: The scale may need to be initialized if it is moved or bumped. General Operation 1. Place the scale on a flat, hard surface. Carpeted or uneven floors may affect accuracy. 2. Step on the scale, positioning your feet evenly on the scale platform. Stand still while the scale measures your weight. 3. When your weight stabilizes, the display will show your weight. remain on the screen for a few seconds. The d

Use SCREW DRIVER to attach POLE to BASE by inserting and turning the 2 screws tightly Screws 6. Slide POLE COVER down 5 Setting The Zero Point and Balance Before using the scale for the first time or when another place, you must set the zero point and weighing yourself. Zero Point 1. With nothing on the PLATFORM, adjust POINTER to ZERO using ADJUSTING KNOB found under DIAL, on the unit’s back side. Balance Adjusting Knob 1. Place the scale on a flat, firm surface 2. Turn 6 LEVELING FEET until th