Go-Go Babyz will repair or replace, at its sole option, the defective product within that one-year time period. If you have a problem with your Go-Go Babyz product or are not satisfied with it, please contact Go-Go Babyz Customer Service at 1.888.686.2552. This express limited warranty does not cover: (1) Pick-up, delivery, or freight charges. (2) Corrosion caused by improper storage or failure to reasonably protect the product from salt water and adverse conditions. (3) Deterioration due to lac

Model # 8181BT Nursery Center & Playard Instruction Manual Convenience through Innovation and thoughtful design 03.04 Nursery Care Center & Playard LXI Read all instructions BEFORE assembly and USE of Playard. Keep Instructions for future use. WARNING: FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH FROM ENTRAPMENT, STRANGULATION, SUFFOCATION, ETC. INFANTS CAN SUFFOCATE: IN GAPS BETWEEN AN EXTRA MATTRESS AND SIDE OF PRODUCT, OR ON SOFT BEDDI

Tighten the harness to be snug around the child's waist and over the child's shoulders Please see figure 12a. WARNING: Avoid serious injury from falling or sliding out. Always use the safety harness. STRANGULATION HAZARD: Child can strangle in loose straps. Never leave child in seat when straps are loose or undone. • To release, apply pressure to both sides of each male clip until the clip is released. See figure 12b. This process requires a moderate amount of effort so as to prevent an accident

MODEL # 1638CT Providence Ridge Travel System Instruction Manual 11.06 Convenience through Innovation and thoughtful design WARNINGS WARNING: Please follow all of these instructions to ensure the safety of your child. Keep these instructions for future reference. WARNING: Failure to follow these instructions could result in serious injury or death. Avoid serious injury from falling or sliding out. Always use the seat belt and insure that the child is properly positioned according to these instru

Child Tray Figure 5. Solid Cap Locking Cap Rear Wheels Stroller Figure 1. Base Car Figure 2. Rear Axle Assembly Hub Cap Front Wheels 3 Figure 4. Parent Tray * To attach the front child tray, push the angled tray onto the post at the end of the right armrest, while pressing downward on the snap button, until locked into place. Please see figure 7. Rotate the tray downward until latched onto the left armrest. Please check that the snap button comes through and securely latches the tray in place. P

For infant car seat.s instructions, please refer to the manual located under the car seat MODEL # 1956CT Serengetti ™ Travel System Instruction Manual Convenience through Innovation and thoughtful design Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved. WARNINGS * Purses, shopping bags, parcels, diaper bags or accessory items may change the balance of the stroller and cause a hazardous, unstable condition. * The maximum weight that can be carried in the storage basket is 5 lbs. The

5 ATTACHMENT OF THE BABY TREND INFANT CAR SEAT * To attach the Baby Trend Infant Car Seat, place seat back in the partially reclined position as described in the seat back positioning section following. Please see figure 25 and 26. * Check that the front child tray is firmly attached to the stroller armrests. Pull rearward on the rear edge of the front child tray cover while lifting upward on the tray cover. Please see figure 19 and 20. Remove the tray cover and store in the pocket in the rear o

Model #: 8207BCC DELUXE TREND NURSERY CENTER Instruction Manual 05.07 Convenience through Innovation and thoughtful design Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved. WARNINGS WARNING: FAILURE TO FOLLOW THESE WARNINGS AND THE ASSEMBLY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH FROM ENTRAPMENT, STRANGULATION, SUFFOCATION, ETC. WARNING: INFANTS CAN SUFFOCATE: IN GAPS BETWEEN A MATTRESS TOO SMALL OR TOO THICK AND PRODUCT SIDES, ON SOFT BEDDING. NEVER ADD A MATTRESS, PIL

Please follow the following instructions for proper installation of the Vante. Front Seat: 1. Remove (unscrew) Crossbars A1, B1, C and D from the Double Snap-N- Go® frame. Retain the screws you remove. 2. Attach Crossbar C on top of Crossbar B1, with the bent side of B1 facing downward, to the Double Snap-N-Go® frame using the two holes labeled #2. Use the two long screws provided separately. Please see figure 1. 3. Attach Crossbar B1, taken from the rear of the Double Snap-N-Go® frame, to the D

To Contact us: Baby Trend, Inc.Parts Hotline: 1567 S. Campus Ave.(800) 328-7363Ontario, CA 91761 8:00 a.m. and 4:30 p.m. Pacific Coast Time 1 ASSEMBLY: • Remove stroller from box. The front wheels, rear wheels and parent tray need to be installed prior to use. • To attach the front wheels, unfold stroller as described in the section following. See fi gure 1. Lean the stroller backwards so that it rests on the handle and rear frame tubes and the front wheel bayonet are pointing upward. Position t