Votes - 2, Average rating: 3.5
(
)
)
|
manual abstract
Please follow the following instructions for proper installation of the Vante. Front Seat: 1. Remove (unscrew) Crossbars A1, B1, C and D from the Double Snap-N- Go® frame. Retain the screws you remove. 2. Attach Crossbar C on top of Crossbar B1, with the bent side of B1 facing downward, to the Double Snap-N-Go® frame using the two holes labeled #2. Use the two long screws provided separately. Please see figure 1. 3. Attach Crossbar B1, taken from the rear of the Double Snap-N-Go® frame, to the Double Snap-N-Go® frame using the two holes labeled #7. Use the two screws that you removed in step 1. Please see figure 1. Rear Seat: 1. Remove (unscrew) Crossbars A2, B2, and B1 from the Double Snap-N- Go® frame. Remove the Car Seat Straps from the Double Snap-N-Go® frame. Retain the screws you remove. 2. Attach Crossbar D, removed in the Front Seat step 1 above, to the Double Snap-N-Go® frame using the two holes labeled #5. Use the two screws that you removed in step 1. Please see figure 2. 3. Attach both Car Seat Straps to the Double Snap-N-Go® frame using the two holes labeled #4. Use the two screws that you removed in step 1. Please see figure 2. Insertion of the Century® Vante Infant Car Seat 1. With one hand grasp the car seat handle (in its upright, carrying position) 2 and gently place the seat, so that the baby faces the rear of the Double Snap-N-Go®, onto the Double Snap-N-Go® so that the large groove on the seat bottom, nearest the head-end of the seat, hooks over the Crossbar C/ B1 combination in the front position or hooks over the top section of the Double Snap-N-Go® frame in the rear position. Check that the seat locked onto the Crossbar or frame. See Figure 3. FOR SAFE OPERATION, IT IS VERY IMPORTANT THAT THE SEAT LOCK SECURELY ONTO THE CROSSBAR OR FRAME. 2. Feed the Car Seat Straps through the auto belt slots on the infant car seat as shown in Figure 4 and snap the two buckles together. The first time your do this, you will need to adjust the length of the strap for a tight fit around the car seat. FOR SAFE OPERATION, IT IS VERY IMPORTANT THAT THE CAR SEAT STRAP IS ALWAYS TIGHTLY FASTENED OVER THE CAR SEAT. 3. Test for secure installation by moving the car seat in all directions. The car seat should be securely attached to the Double Snap-N-Go®. Removal of the Century® Vante Infant Car Seat 1. Unlock the Car Seat Strap and remove from over the infant car seat. 2. With one hand, grasp the car seat handle (in its upright, carrying position) and with your other hand squeeze the handle on the back of the car seat and lift the car seat upward from the Double Snap-N-Go® frame. See Figure 5. Century® and Vante are the trademarks of their owners. They are not associated with Baby Trend and no approval or endorsement is implied. BarCBarB1Hole#7Hole#2Hole#6BarB1StrapBarDHole#4Hole#5StrapFig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 8 Installation Instructions for Cosco® Designer/Opus 35 The Double Snap-N-Go® will accommodate the Cosco® Designer/Opus 35 Infant Car Seat. Please follow these instructions for proper installation of the Cosco®. Front Seat: 1. Remove (unscrew) Crossbars A1, C and D from the Double Snap-N-Go® frame. Leave Crossbar B1 in hole labeled #4. Remove the Car Seat Straps from the Double Snap-N-Go® frame. Retain the screws you remove. 2. Attach Crossbar B1 (removed from the rear section of the Double Snap- N-Go® frame), so that the bent section faces down, to the Double Snap-N- Go® frame using the two holes labeled #5. Use the two screws that you removed in step 1. Please see figure 1. 3. Attach both Car Seat Straps to the Double Snap-N-Go® frame using the two holes labeled #3. Use the two screws that you removed in step 1. Please see figure 1. Rear Seat 1. Remove (unscrew) Crossbars A2 and B1 from the Double Snap-N-Go® frame. Remove the Car Seat Straps from the Double Snap-N-Go® frame. Retain the screws you remove. 2. Attach Crossbar C (removed from the front section of the Double Snap-N- Go® frame) to the Double Snap-N-Go® frame using the two holes labeled #4. Use the two screws that you removed in step 1. Please see figure 2. 3. Attach both Car Seat Straps to the Double Snap-N-Go® frame using the two holes labeled #1. Use the two screws that you removed in step 1. Please see figure 2. Insertion of the Cosco® Designer/Opus 35 Infant Car Seat 1. With one hand grasp the car seat handle (in its upright, carrying position) and with your other hand squeeze the handle on the back of the car seat and gently place the seat, so that the baby faces the rear, onto the Double Snap-N-Go® so that the rear small grooves on the seat bottom hook over Crossbar B1 for the front position or Crossbar C for the rear position. Release the handle and check that the seat locked onto the bar. See Figure 3. FOR SAFE OPERATION, IT IS VERY IMPORTANT THAT THE REAR LATCHES OF THE SEAT LOCK SECURELY ONTO THE CROSSBAR. 2. Feed the Car Seat Straps through the slots found on the rear of the CarSeat shell as shown in figure 4. Buckle t...