Put the 3 pcs support legs on each position on the base as shown in th« picture. 1-2. Use 3 pcs M8 x 16 mm bolts to join the support legs and base, STEP 2 2-1. Put the post support on the top of 3 pcs support legs . 2-2. Use 6 pcs M6 x 35 mm bolts and nuts to connect the post to the 3 pcs support legs. Tighten the bolts and nuts. STEP 3 Use 4pcs M6x12mm bolts to connect the first piece of the post assembly to the post support. STEP 4 Connect the second piece of the post assembly to the f
The soapy water solution can be applied with a spray bottle, brush or rag to all gas connections. Soap bubbles will appear in case of a leak. WARNING Never leak test while smoking. 3. Turn the gas supply ON. 4. In case of a leak, turn off the gas supply. Tighten any leaking fittings, then turn the gas supply OH and recheck. Contact your dealer or gas supplier for assistance if bubbles continue to appear. 5. Ensure you are using ptumbing (teflon) tape on the threaded parts of all fittings.
power: 13k VV Min.power: 5kVV Please retain this manual for reference. WARNING • READ THE INSTRUCTIONS BEFORE USE • This appliance must be installed in accordance with such regulations as are in force. • This appliance requires installation by a competent person. • Use only in well-ventilated areas. • This appliance shall be not used indoors. • This appliance shall be used for outdoors only. • This appliance shall not be used in basements or enclosed areas. • This appliance has no atmo
A complete gas tightness check must be performed at the installation site due to potential shipment irregularities or excessive pressure being applied to the heater as well as to check final installation of components by the consumer. TO LEAK TEST * Make a soapy solution of one part liquid detergent and one part water. The soap solution can be applied with a spray bottle, brush, or rag. Soap bubbles will appear where a leak is present. * Make certain the safety control valve is in the “OFF” p
Tighten securely. *** IMPORTANT NOTE: be sure to route and keep the electrical cord AWAY from the main body of the heater unit. *** FigT3 Min. Clearances: 83” head unit height 10” from mounting wall 12” from surfaces above the heater head unit 36” from sides and front of head unit 45-55 degree angle of operational spread Route power cord below and away from head unit as show in box 5. ///?*?*//. Correct v/ ///?*’// Wrong Wrong to lock position of head unit. Page 5 *** Important No
safety regulations or equivalent. If you are unsure, consult an electrical service professional. * Avoid the use of an extension cord with this appliance. * Do not place any objects such as furniture, papers, clothing or curtains closer than 3 ft to the front and sides of the heater. A CAUTION NOTE: your IR Heater main body, electrical components & bracket are fully factory assembled. Do NOT attempt to service or disassemble without proper instructions. 3 Head Unit With aluminum shield, p
Oils from your hand could reduce the life of the lamp by causing a heat spot. Recommend using clean cotton or plastic gloves. A clean paper towel may also work. Quartz Halogen Lamp Replacement: * Be sure unit is unplugged from wall outlet! * Remove head unit assembly from wall mounting bracket (refer to step 3 from page 5) * Remove 8 screws from each end of the head unit and pull off end plates (see #2) - Note the placement of the 2 small sheet metal screws on each end plate. Also, note en
Never use a propane tank with a damaged valve connection. " The propane tank must be constructed and marked in accordance with the specifications for LP gas cylinders per the US Department of Transportation (DOT). * The propane tank must be designed to provide for vapor withdrawal from the operating cylinder. * Never connect an unregulated propane tank to the heater. LEAK TESTING * Gas connections on the heater are gas tested at the factory prior to shipment A complete gas tightness check m
* When using outdoors,we recommend using a certified GFI (Ground Fault Interrupt) outlet to protect against electrical shock. * Ensure that the heater mounting bracket is SECURELY fastened to the wall, patio overhang or house eave. * Route electrical cable AWAY from main body of heater which gets very hot. * Do NOT cover or obstruct the main body of the heater during use. * All installations must be in accordance with I.E.E. safety regulations or equivalent. If you are unsure,consult an electric
' 3 ea unit ‘ 6 ea. M6 x 25mm bolts to attach wheel assembly brackets *** IMPORTANT NOTICE *** The installation must conform with local codes or, in the absence of local codes, with the most current version of the National Fuel Gas Code, ANSIZ223.1 ASSEMBLY INSTRUCTIONS STEP 1: 1-1. Place the 3 post mounting brackets on the Cylinder Base as shown. 1-2. Use 3-M8 x 15mm bolts to secure brackets to the base. STEP 1a: 1a-1. Attach wheel assembly brackets to cylinder base. Align holes and po