Votes - 4, Average rating: 3.3
(
)
)
|
manual abstract
A complete gas tightness check must be performed at the installation site due to potential shipment irregularities or excessive pressure being applied to the heater as well as to check final installation of components by the consumer. TO LEAK TEST * Make a soapy solution of one part liquid detergent and one part water. The soap solution can be applied with a spray bottle, brush, or rag. Soap bubbles will appear where a leak is present. * Make certain the safety control valve is in the “OFF” position (at the control panel of the head unit). * Turn the gas supply “ON” at the propane cylinder valve. Apply/spray several drops on the regulator hose to gas inlet hose connection, and the regulator to tank cylinder connection, (small bubbles indicate a leak) * If a leak is present, turn “OFF” the gas supply, loosen and then re-tighten and leaking fittings, turn gas supply “ON” again and recheck. Repeat as needed. tt~C7nmGl№TBTTVir(J5E BE CAREFUL: When certain material or items are left under this space heater while in use, they will be subjected to radiant heat and could be seriously damaged! The heater is primarily for heating of outdoor patios, decks, spas, pools and outdoor home working areas. This unit is designed for RESIDENTIAL use only! Always ensure that adequate fresh air ventilation is provided. Follow the MINIMUM spacing tolerances as indicated AT ALL TIMES! The installation must conform to local codes, or in the absence of local codes, with the standard for the storage and handling of liquid petroleum gases, ANSI/NFPA 58 or NFGC, ANSIZ 223.1-1998 The heater must be placed on stable, level firm ground. Never operate in an explosive atmosphere. Keep away from areas where gasoline or other flammable liquids or vapors are stored or used. In very strong winds, turn off the heater, turn off the gas cylinder valve and remove the heat reflector hood. Then move the heater to a sheltered location. Do not move heater while it is still hot. PAGE 10 A CAUTION L- *** IMPORTANT NOTICE *** i-Do NOT return to place of purchase!!!! Please contact our Toll Free Hotline: (866) 985-7877 E-mail, cservice@welltraveled.net STEP 8: OPERATION & STORAGE 8-1. OPERATION 1 Open the gas cylinder valve. 2 Turn the control knob half way between the small flame and the large flame symbols, aligning to the calibration mark 3. Depress (press down) the control knob and then push the RED electronic igniter button to ignite the main burner, repeat until the main burner ignites Keep the control knob fully depressed for an additional 30 seconds after the burner ignites, then release the control button 4 To increase the flame,turn the control knob dockwise.To decrease the flame,turn the control knob counter clockwise 5. To turn off the appliance: press down the control knob and turn counter clockwise to the off position 6. Wait 5 minutes before re lighting the unit /.Completely shut off and close gas cylinder valve. *** IMPORTANT NOTICE *** Establishing a burner ignition for the FIRST time or after changing the cylinder tank may take up to 2-3 minutes in order for the gas to purge through the feeder lines. ‘“NOTE: Main burner may also be lit using a MATCH*** CAUTION: Be aware of gas build-up when lighting with match-especialiy alter holding down control knob. If you swell gas, WAIT 5 minutes lor gas to dissipate before lighting. Manual Lighting: place a sticker lighter thru the large hole at the bottom of the burner unit while following the lighting procedures above. Electric Ignitor - Battery Replacement Requires 1-AAA battery - alkaline type recommended. Unscrew rubber/vinyl housing. Replace battery - negative (flat) end of battery facing out. Gently reattach housing by threading into place. WARNING: Read the installation, operation, and maintenance instructions thoroughly BEFORE operating, installing or servicing this equipment. Improper use, adjustment, service and/or maintenance can cause serious injury or damage to your property. Minimum Clearance to adjacent combustible surfaces is as follows ‘Sides - 24' 'Top - 36" The Gas Supply Must be turned "OFF" at the LP Gas Cylinder when this appliance is not in use. After appliance shut down. Do NOT touch or move unit for at least 30 minutes. This allows for proper cooling of heater components. **• NOTICE *** Bminaliie FIRST TIME use only, II is normal to experience a small amount of smoke coming from the reflector hood This is due to the bum off of the protective coating applied during the manufacturing process during the manufacturing process PAGE 11 *** IMPORTANT NOTICE *** - Do NOT return to place of purchase!!! Please contact our Toll Free Hotline: (866) 985-7877 E-mail: cservice@welltraveled.net *** BURNER OPERATION *** * The burner head unit emitter screen will burn bright red when normally. The heat generated is VERY INTENSE. Note: It is for some discoloration of the emitter screen after use. * The burner flame will normally show blue wi...