Box 1596 Murphy, NC 28906 U.S.A. Tel No. 828-835-9765 Fax No. 828-835-9685 Important Read these instructions carefully before installing, operating, servicing or repairing this tool. Keep these instructions in a safe accessible place. Product Type 1/8" (3 mm) Pencil Air Die Grinder Model No/Nos 5978A RPM 54,000 Cycles Per Min. C€ Serial No. Product Net Weight 0.44 lbs 0.20 Kg Recommended Use Of Balancer Or Support N0 Recommended Hose Bore Size - Minimum 5/16 ins 8 mm Recommended

If practical and possible, try to clear unnecessary obstructions before starting work. -Always use air hose and couplings with minimum working pressure ratings at least 1 1/2 times the maximum working pressure rating of the tool. Foreseen Use Of The Tool - 5979A This die grinder is primarily designed for use with bonded abrasive mounted point grinding wheels. It may also be used with steel rotary files and carbide burrs provided their speed rating matches or exceeds the speed of the grinder.

rated as being suitable for use with impact wrenches. - Prolonged exposure to vibration may cause injury. -Read all instructions before using this tool. Ail operators must be fully trained in its use and aware of these safety rules. - Do not exceed the maximum working air pressure. - Use personal protection equipment as recommended. - Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects and

Take off O-ring (44) and hook out oil seal (43) and press out anvil bushing (42) from housing (1). Grip hammer cage (34) and pull off the hammer mechanism assembly. Take off anvil spacer (38) and from hammer cage (34) pull out anvil (37). (45) or (50), spring (51) and thrust button (52). Push out 2 hammer pins (36) from hammer cage (34) to release 2 hammers (35) and carefully note how the two hammers (35) are located to hammer cage (34) by hammer pins (36) for reassembly). If replacements are re

It is always recommended that the tool is used when standing on the solid floor. It can be used in other positions, but before any such use, the operator must be in a secure position having a firm grip and footing and be aware that when loosening fasteners the tool can move quite quickly away from the fastener being undone. An allowance must always be made lor this rearward movement so as to avoid the possibility of handferm/body entrapment. Putting Into Service Air Supply Use a clean lubrica

Disconnect the air line and pour into the hose adaptor a teaspoonful (Sml) of a suitable pneumatic motor lubricating oil preferably incorporating a rust inhibitor. Reconnect tool to air supply and ran tool stowty lor a few seconds to allow aif to circulate the oil. ff tooi is used frequently, iubricate on daiiy basis and if tooi starts to slow or lose power. Si is recommended that the air pressure at the tooi while the loot is «inning is SO psi/6.2 bar. Operating Select a suitable mounted poi

Take out collet (36) and grip housing (1) in a Vise fitted with soft jaws on the flats at the rear end and with a peg spanner or a punch unscrew clamp nut (33) - left hand thread - and grtp chuck spindle (34) and pull out the spindle assembly from the angle head housing (28). Support the underside of clamp nut (33) and tap the and of spindle (34) to drive the spindle through and to separate spindle (34), key (35), clamp nut (33). bearing {24) and bevel gear (30). If bearing (16) was 00» withdraw

When first lubricating a tool or if the tool exhaust has a high oil content, do not allow the exhaust air to come near very hot surfaces or flames. -Never lay the tool down until the working attachment has stopped moving. -When the tool is not in use, shut off the air supply and press throttle triggerllever to drain the supply line. If the tool is not to be used for a oeriod of time. first lubricate. disconnect from air supply &d store in a dry average room temperature environment. -If the tool

1 SAFETY MESSAGES 1 A WARNING 1 Operator Instructions PersonalSafety Equipment Always Read Instructions Before Includes:1 YES 1 0 "sing Power Tools 1 Use -Safety Glasses Safety Rules Use -Safety Gloves @ Always Wear Safety Goggles ores seen Use Work Stations Use -Safety Boots @ Wear Hearing Protection Putting Into Service Use -Breathing Masks A T Avoid Prolonged Exposure o Vibration Operating Use -Ear Protectors YES Disrnantlina and Assernblv. Safety rules when using a 509215092L Impact Tool -Us

If you do not have this equipment, you can not service this tool. Hypot testing is a safety test required by Underwriter’s Laboratories. It basically ensures that there are no live metal parts exposed on the product. This condition could occur if, for instance: 1. A housing screw went through a wire. 2. A wire was stripped back too far and the bare wire contacted a bearing or the driveshaft. 3. A wire was damaged and came into contact with a bearing or the driveshaft. This is a very serious