• Automatically turns lighting off. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). This package includes: Mounting Bolt Plastic Hanger Rubber Plug Lamp Holders 2 Shells Cover Plate Gasket Sensor Light Control Mounting Strap 2 Wire Connectors 6 Screws 2 Flood Lamps (3 sizes included) (some versions) Requirements • The Light Control requires 120-volts AC. • If you want to use Manual Mode, the control must be wired through a switch. • Som

• Automatically turns lighting off. • Photocell keeps the lighting off during daylight hours. • LED indicates motion was sensed (day or night). This package includes: Plastic Hanger 6 Screws Gasket (3 sizes included) 1 Halogen Lamp Sensor 3 Wire Connectors Light Control Mounting Strap Mounting Bolt Rubber Plug Light Shield Requirements • The Light Control requires 120-volts AC. • If you want to use Manual Mode, the control must be wired through a switch. • Some codes require installation by a qu

Keep it with your other important papers. ® INSTALLATION AND OPERATING INSTRUCTIONS 55505 Rev. B 07/99 PENINSULA MODEL VPN36 3-SIDED, WOODBURNING FIREBOX FOR YOUR SAFETY • Do not store or use gasoline or any other flammable vapors or liquids in the vicinity of this or any other appliance. • Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies. • Do not place clothing or other flammable materials on or near the appliance. • NEVER leave chi

6' max. 6' min. 12' max. 7' min. 18' max. 8' min. 20' max. Note: Vertical (V1) + Vertical (V2) = 20' max. Figure 30 - Vertical Rigid Venting Configuration Using Two 90° Elbows 14 106573 OWNER’S MANUAL VENTING INSTALLATION Continued HIGH ALTITUDE INSTALLATION Your Vanguard direct-vent fireplace has been AGA tested and approved for elevations from 0-2000 feet and CGA certified for elevations from 0-4500 feet. When installing this fireplace at an elevation above 2000 feet (in the USA), you may need

This appliance is only for use with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases, unless a certified kit is used. *Aftermarket: Completion of sale, not for purpose of resale, from the manufacturer. — Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. — WHAT TO DO IF YOU SMELL GAS : • Do not try to light any appliance. • Do not touch any electrical switch; • Do not use any

• Use new black iron or steel pipe. Internally tinned copper or copper tubing can be used per National Fuel Gas Code, section 2.6.3, providing gas meets sulfide limits, and where permitted by local codes. • An ANSI approved 1/8” NPT pressure tapping point must be installed immediately upstream of the gas supply connection to the fireplace • A sediment trap may be install upstream of the fireplace to prevent moisture and contaminants from passing through to the fireplace control and burner. Failu

Follow the gas supplier's instructions • if you cannot reach you gas supplier, call the fire department. 4. Never install the fireplace • in a recreational vehicle • where curtains, furniture, clothing or other flammable objects are less than 42" from the front, top or sides of the fireplace • in high traffic areas • in windy or drafty areas 5. This fireplace reaches high temperatures. Keep children and adults away from hot surfaces to avoid burns or clothing ignition. Fireplace will remain hot

. . . 4" • Top spacer. . . . . . . . . . . . . . . . . . . . . . . . . . 0" See Figures 3 and 4. CAUTION: Do not block required air spaces with insulation or any other material. Do not obstruct effective opening of appliance with any type of facing material. Figure 4 - Clearances from Top View Mantel Clearances Woodwork, such as wood trims, mantels and other combustible materials, should not be placed within 7" of the opening of this appliance (see Figure 5). Combustible material above the firep

Check for spark at electrode and pilot. If no spark and electrode wire is properly connected, replace ignitor 2. Check gap at electrode and pilot. Gap should be 1/8" for strong spark. If gap is correct but no spark, replace pilot 3. Contact your local NG or LP gas supplier 4. Refill supply tank (propane/LP only) Troubleshooting Electronic ignition system Note: Before troubleshooting the system, make sure the gas shutoff valve is ON. The two most common causes of a malfunctioning gas appliance ar

Orange flame will also be present. Open window to vent smell. This will only last a few hours. 1. STOP! Read the safety information, column 1. 2. Set the thermostat to lowest setting (if applicable). 3. Turn off wall switch. 4. Open control access panel or louver. 5. Smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information in column 1. If you don’t smell gas, go to the next step. 6. Turn the main burner wall switch to the ON position for ignition. The