If just after burner is lit or shut off tracting while cooling noise is excessive, contact qualified service person Fireplace produces unwanted odors 1. Fireplace burning vapors from paint, hair 1. Ventilate room. Stop using odor causspray, glues, etc. (See IMPORTANT ing products while fireplace is running statement above) 2. For propane/LP gas, low fuel supply 2. Contact local propane/LP supplier 3. Gas leak. SeeWarning statement at 3. Locate and correct all leaks (see Gas top of page Line Hook
To enhance the look of the hearth you may optionally place the lava rock provided around the front and sides of the burner. INSTALLATION Continued NOTICE: Do not put lava rock inside the burner pan or around the air mixer fitting. Placing lava rock inside the burner pan or blocking the openings of the propane/LP air-mixer could cause performance problems. INSTALLATION Log Placement For P324/VP324 Models Log Placement for P325(B)/VP325(B) Models Figure 26 - Installing Logs 1 and 2 Figure 27 - Ins
Example 3:Shows a single offset at 45° degrees of inclination and therefore the lateral length at 10 feet of offset does not have to meet the 75% percent rule. In each case the offsets must be supported and firestops must be positioned wherever the vent must pass through a sub-floor, ceiling joist or an attic overhang. The vent pipe must terminate vertically into a listed type vent cap and extend a sufficient height through an approved roof flashing, roof jack or a roof thimble. At all points th
Brick (B Models) Rear Refractory, Std. Brick (B Models) Bottom Front Refractory, Std. Brick Bottom Rear Refractory, Std. Brick Firebox Support Leg Box Assembly Screen Rod Firebox Top Assembly Screw, #10x5/8 Mod. Tr. Blk. Ox Damper Door Assembly Firebox Face Smoke Deflector Fireplace Top Insulation Grate Assembly Burner Assembly Burner Pan Burner Tube Burner Bracket Pilot Shield Burner Clamp Nut, #10-24 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 2 1 2 1 1 1 1 1 1111111 24-10 24-11 24-12 25 26 27 28 29 30 31 3
Models CD32M sereies, CD36M-A series and CD42M-A are heat circulating gravity direct-vent fireplaces with sealed combustion chamber. These fireplaces use millivolt gas control valve and millivolt ignition system. These fireplaces are convertible with the standard setup as natural gas. Conversion may be performed by the O.E.M. mobile home builder or by a qualified service person on-site. If you are uncertain as to what gas your unit is equipped for, please check the rating plate located inside of
3. When installation of vent pipe is complete, in stall vent termination. Depending on the location of your fireplace, you will vent vertically or horizontally. 4. Allow 1" of pipe to protrude from internal wall, depending on wall thickness. See Figure 7. 5. For horizontal installation, an optional siding standoff may be installed between the vent cap and the exterior wall. Secure horizontal vent cap to standoff. Secure standoff/vent cap assembly to wall (see Figure 7). Do not seal termination t
Bubbles forming show a leak. Correct all leaks at once. Do not operate any appliance if a leak is detected. Figure 12- Typical Exterior Wall Gas Shutoff Installation Key Extension Shutoff Valve Figure 13 - Gas Line Routing Figure 14 - Sediment Trap PILOT ADJUSTMENT The pilot or electrode assembly is factory preset for the proper flame height. Alterations to these settings may have occurred during shipping and handling. If this is the case, some minor readjustments may be necessary and should be
Figures 5 and 6 show the minimum allowable distances from various combustible mantle components in relation to the fire- 1 1/2" (38mm) 3" (76mm) Max. 6" (152mm) Max. A B Outer Surround TOP VIEW SAFE ZONE Combustible Material May place opening. Be Used Max. Spacer 3" (76mm) 1 1/2" (38mm) Max. B 6" (152mm) A 12" (229mm) Combustible Materials Header Perpendicular Wall M36E(B,H) M42E(B,H) VM36E(B,H) VM42E(B,H) A 9" (229mm) 6" (152mm) B 12" (305mm) 9" (229mm) Figure 6 - Side Clearances - Top View (Cr
This will prevent the entry of cold air by means of conduction through the total bottom of the appliance. (see Figure 32). CAUTION: Air inlet ducts are not to terminate in attic space. Note: Glass door may be heavy for some individuals. If this is the case, please request help from someone else. The M36E, VM36E, M42E and VM42E B-vent fireplaces are approved for use with optional bi-fold glass doors (see Accessories, page 27). The glass panels may be ordered and installed anytime after the firepl
If damaged, promptly inform dealer or distributor where you bought the product. Safely retain these items for later installation. For more information, visit more information, visit 108796-01E 4 4 INTRODUCTION Before You Begin INTRODUCTION Models M36E(B,H), VM36E(B,H), M42E(B,H) and VM42E(B,H) are vented gas fireplaces that use an electronic gas control valve and electronic ignition system. A 6" B-Type venting system and a listed type vent cap are not supplied but are required for proper operati