• Always turn the power off at the power outlet before you insert or remove a plug. Remove by grasping the plug - do not pull on the cord. • Turn the power off and remove the plug when the appliance is not in use and before cleaning. • Do not use your appliance with an extension cord unless this cord has been checked and tested by a qualified technician or service person. • Always use your appliance from a power outlet of the voltage (A.C. only) marked on the appliance. • Close supervision is ne
The 18 lb capacity 7.0 cu. ft. cylinder delivers superior tumble action to handle permanent press fabrics. Silver Lining Dryer Cylinder with galvanized steel interior won’t corrode, chip, crack or pit in normal use. The NetMaster® Control makes ^ programming the machine a breeze. The easy-to-read display shows vend price, cycle time and cycle status. The Touch Pad Control allows for - easy selection of four temperatures and cycles. Large, Upfront, Secured Lint Filter is convenient to reac
• ••••• Collector Venting While it is preferable to exhaust tumblers individually to outdoors, a main collector duct may be used if it is sized according to Figure 3. NOTE: This illustration indicates minimum diameters, and should be increased if collector length exceeds 20 feet (6.1 m). Collector duct may be rectangular in cross section, as long as area is not reduced. Provisions should be made for lint removal and cleaning of collector duct. Collector duct must be tapered, as shown in Figure 3
55 Cylinder Door Strike ............................................... 55 Drive V-Belt ............................................................ 56 SECTION IV PREVENTIVE MAINTENANCE INSTRUCTIONS Daily ....................................................................... 57 Monthly................................................................... 57 Quarterly ................................................................ 58 Biannually......................................................
NATURAL GAS service must be supplied at 6... ± 1... inch water column pressure (1.62 ± .37 kPa). L.P. GAS service must be supplied at 11 ± .3 inch water column pressure (2.74 ± .07 kPa). If gas service is not same as that specified, DO NOT CONNECT THE GAS LINE TO TUMBLER! It will first be necessary to convert gas burner orifice and gas valve. IMPORTANT: Any product revisions or conversions must be made by the Manufacturer’s Authorized Dealers, Distributors or local service personnel. . WARNING T
7. All manually operated models are factory-equipped with an emergency stop button located on the front panel. If the emergency stop function is desired on coin-operated models, an external emergency stop switch may be installed as specified on the machine wiring diagram. NOTE: Activation of the emergency stop switch stops all machine control circuit functions, but does not remove all electrical power from machine. To reduce the risk of fire, electric shock, serious injury or death to persons wh
STEAM CONNECTIONS (Steam Drying Tumblers) INSTALLING STEAM SOLENOID VALVE AND MAKING STEAM INLET CONNECTIONS High pressure machines require a (constant) 80 to 100 psig (5.62 to 7.03 kg/sq. cm) steam service for optimum operation. Low pressure machines require a (constant) 10 to 15 psig (.70 to 1.05 kg/sq. cm) steam service for optimum operation. The following steps outline procedure for installing steam solenoid valve and connecting steam service. a. Install a manual shut-off gate valve in conde
380 / 415 V 3 Phase, 50 Hz. Minimum Wire Size 14 AWG (2.081 mm.) 14 AWG (2.081 mm.) 14 AWG (2.081 mm.) Circuit Breaker 15 AMP 15 AMP 15 AMP Poles 2 3 3 Figure 16 ELECTRIC DRYING TUMBLERS NOTE: DO NOT use aluminum wire. ELECTRIC DRYING TUMBLERS 380 V, 3 Ph, 50 Hz. 415 V, 3 Ph, 50 Hz. Minimum Wire Size 6 AWG (13.32 mm.) 6 AWG (13.32 mm.) AMP Rating 48 Amp 45 Amp Circuit Breaker 50 Amp 50 Amp Poles 3 3 Figure 17 GROUNDING INSTRUCTIONS Drying tumbler must be grounded. In event of malfunction or brea