The owner’s manual uses the words course and course selection, while the labels display programs and program selection. To lessen confusion, please remember that wherever you come across the word “course” in the owner’s manual, you need to replace it with the word “program.” OPTIONAL POWER ADAPTER With the C842 or C846i product, if you choose to purchase the optional power adapter, you must also purchase the internal cable kit. This kit supplies a cable, bracket and fasteners that allow the po

Do not attempt installation on your own as you could void the Precor limited warranty. If you need assistance, please see Obtaining Service in your owner’s manual. Diagram 1 Loosen nut to adjust seat tilt. Seat- Nut- Wrench- Seat Post SEAT ADJUSTMENT On the C846i and C842, you can adjust the seat tilt by taking the following steps: 1. Loosen the nut beneath the seat using a 17 mm (11/i6-inch) box-end wrench or crescent wrench. Refer to Diagram 1. P/N 47563-101 February 27, 2004 Diagram

The Club Setting Program also enables you to limit workout time on the cycle so more people can use it. Instructions on how to use the program are found in this section. Installation Requirements Follow the installation requirements below when installing the cycle. If you do not install the cycle according to the following guidelines, you could void the Precor warranty. • Set up the EC860 cycle on a solid, flat surface. • Use the appropriate voltage outlet and grounding as specified on the cycle

Read and observe the following safety guidelines when using the EC850 Professional Cycle: • Read the Owner’s Manual and follow all instructions. These instructions were written to ensure your safety and to protect the cycle. Note for Club Owners: To ensure the proper use and safety of the EC850 cycle, make sure that all users review this manual. Please make this manual a part of your training program. • Assemble and operate the cycle on a solid, level surface. • Never allow children on the cycle

Diagram 3 Handrail Nut plate Lower handrail clamp C O M M E R C I A L P R O D U C T S D I V I S I O N f. To secure the handrail inside the clamp, use the 5/32" hex key provided. Do not overtighten the bolt or damage may occur to the clamp. Note: After extensive use, vibrations from the treadmill may cause the bolts to loosen. You may need to periodically inspect the bolts and, if necessary, tighten both the upper and lower handrail clamp bolts using the hex keys provided. g. Return to the upper

Each kit comes complete with all the hardware required to install a handrail on one side of the treadmill. If you wish handrails on both sides of the treadmill, you must order two (2) option kits. When you receive the Handrail Option kit, check its contents with the list below: Note: If you purchase both handrails, check the contents of both kits with the list below: Handrail Option Kit Contents One handrail One upper end clamp One upper center clamp Three large bolts (two 5/16 - 18 x 2.5 and on

Discard the covers and the bolts. Replacement bolts and clamps are in this option package. Important: If you are installing both handrail options, install a handrail on one side before proceeding to the other side of the treadmill. Attach the front portion of the handrail first. This helps you determine where to position the lower handrail clamp. Electronic console Bolt End clamp Center clamp Handrail end cover Upper frame Finger guard Rear roller Bolt Attaching the front section of the handrail

If you wish handrails on both sides of the treadmill, you must order two (2) option kits. When you receive the Handrail Option kit, check its contents with the list below: Note: If you purchase both handrails, check the contents of both kits with the list below: Handrail Option Kit Contents One handrail One upper end clamp One upper center clamp Three large bolts (two 5/16 - 18 x 2.5 and one 1/4 - 20 x 2.5) One star washer One nut plate One lower clamp One 5/32" hex key One 3/16" hex key Note: T

Important: If you are installing both handrail options, install a handrail on one side before proceeding to the other side of the treadmill. Attach the front portion of the handrail first. This helps you determine where to position the lower handrail clamp. Electronic console Bolt End clamp Center clamp Handrail end cover Upper frame Finger guard Rear roller Bolt Attaching the front section of the handrail. Diagram 2 Upright support Handrail Guide rail Side rail Nut plate C O M M E R C I A L P R

.......... 4 Unpacking the Equipment ........................................................................................................ ... 4 Important Safety Instructions .................................................................................................. .... 4 2 2 Preparations..................................................................................................... 5 Required Tools..................................................................................