Rectangular shaped metal liner available for on-site Wood Hood construction, Figure 4. 4. The ventilation system (power module and ducting system) is not included and must be purchased separately. B. Installation: Metal Liner - T-Shaped, Figure 3 1. Measure up 6 1/8 from the bottom of adjacent cabinets. Scribe a level line horizontally across depth of both cabinets. 2. Raise Metal Liner so that bottom edge of liner is level with scribed lines. Use four (4) #8 x 1/2” screws provided to attac

Box 4047 ISO 9001 Certified Stamford, CT 06907-0047 TEL: (203) 359-1660 FAX: (203) 359-7700 e-mail: info@omega.com Canada: 976 Bergar Laval (Quebec) H7L 5A1 TEL: (514) 856-6928 FAX: (514) 856-6886 e-mail: info@omega.ca For immediate technical or application assistance: USA and Canada: Sales Service: 1-800-826-6342 / 1-800-TC-OMEGA® Customer Service: 1-800-622-2378 / 1-800-622-BEST® Engineering Service: 1-800-872-9436 / 1-800-USA-WHEN® TELEX: 996404 EASYLINK: 62968934 CABLE: OMEGA Mexico: (001) 8

This is done by using four connecting leads to the device and connecting the V+ and I+ leads to the anode and the V– and I– leads to the cathode as shown in Figure 1. The exact point at which the connecting leads are soldered to the device leads results in negligible temperature measurement uncertainties. In a two-wire measurement configuration, the voltage connections (point A in Figure 1) are made near or at the current source, so only two leads are actually connected to the device. Some loss

Phone: (717) 561-1105 Fax: (717) 561-1298 E-mail: OMEGAUS@aol.com OmegaProducts, Inc. Harrisburg, PA 17111 4523, U.S.A. Phone: (717) 561-1105 Fax: (717) 561-1298 E-mail: OMEGAUS@aol.com Omega. . . A Legendary Name In Fresh Juice E x t r a c t i o n . INSTRUCTION MANUAL FOR THE OMEGA JUICER 1000 AND 500 HOUSEHOLDANDCOMMERCIALUSE I M P O RTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed including the following: • Read all instructions. • To prote

OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE AND ALL IMPLIED WARRANTIES INCLUDING ANY WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive and the total liability of OMEGA with respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall not exc

This output will drive any OMEGA® flow ratemeter, counter, controller or pulse input data acquisition board. Unpacking Remove the Packing List and verify that you have received all equipment. If you have any questions about the shipment, please call the Customer Service Department. When you receive the shipment, inspect the container and equipment for any signs of damage. Note any evidence of rough handling in transit. Immediately report any damage to the shipping agent. NOTE The carrier will no

Normal system filtrsitions should be sufficient. Systems which do not have any filtration should be equipped with at least a 200 m6sh sjeve or 74 micron filter. Most hydraulic systems would already have a much finer filtration. Within the cartridge dirt or sealing agents, such as Teflon tape, may lodge within and cause malfunction. If a malfunction does occur and you are using proper filtration, we would recommend disassembly and cleaning. This Can be done as follows: On clean bench, remove sm

These units feature an SPDT switch, which can be triggered at any point along the flow range FEATURES • Strong, completely sealed die cast aluminum body, water and oil tight • Forrped double sealed aluminum cover (with lip) anodized • Unbreakable Lexan window (full cover) • Oversize neoprene cover gasket matches with double ribbed lip of die cast body. Other seals — Buna-N • Chrome plated pan head cover screws with screw retainers • Wire guards • Easy wire top screw micro switch • Mount

INSTALLING.....................................................................................................................................4 2.1 LAYOUT...........................................................................................................................................4 2.2 JUMPER SETUP..................................................................................................................................5 2.2.1 JP0 ~ JP15 Analog Input R/C Filter ...............