in correct position as illustrated (fig 1). Replace cover. 2 COVER TIP UNIT BASE RECEPTACLE 1 SLIDE HOW TO MOUNT THE TIP (2) • Align tip base over unit receptacle. Push inward until tip is fully seated on base. •To remove ensure tip has cooled. Insert tip remover plate supplied with unit at base of tip and push tip away from base. OPERATING INSTRUCTIONS • Move slide switch forward to ON position. (Push button will not operate in OFF position of slide switch for your safety.) • Push button, pilot
• Shake gas container a few times to warm fuel up. • Make sure the Fuel Adjustment Knob is in the “OFF” position (fully clockwise). • Insert the Butane container nozzle tip vertically down into the unit gas valve refill opening. Use a pumping action for best results (Figure 1). • After filling, allow a few minutes for the gas to stabilize. GAS 1 IGNITION •Turn the Fuel Adjustment Knob counter-clockwise 1 full turn. (Figure 2) • To Ignite: Push Safety Slide Bar up and hold while depressing Igniti
Become familiar with all controls for safety. Lisez ce manuel entierement avant de commencer a utiliser l'outil. Familiarisez-vous avec tous les controles de securite. Lea completamente este manual antes de tratar de usar esta herramienta. Para mayor seguridad, familiaricesecon todos los controles. Exhaust opening Orifice d'echappement Salida de escape Gas open lever Levier d'admission de gaz Palanca de abertura de gas Gas control lever Levier de controle de gaz Palanca de control de gas Made in
Becomefamiliar with all controls for safety. Lisez ce manuel entierement avant de commencer a utiliser l'outil. Familiarisez-vous avec tous les controles de securite. UL® Gas filling nozzle Lea completamente este manual antes de tratar de Bec de remplissage usar esta herramienta. Para mayor seguridad, famil de gaz Boquilla de carga de gas iaricese con todos los controles. Overall length 8.24 in Diameter 0.95 in Longueur totale • Largo total 210 mm Diametre • Diametro 24 mm Weight (when gas fille
10. At the end of each work session put the paint chips and debris in a double plastic bag, close it with tape or twist ties and dispose of properly. 11. Remove protective clothing and work shoes in the work area to avoid carrying dust into the rest of 3 Important Safety Instructions (cont’d) the dwelling. Wash work clothes separately. Wipe shoes off with a wet rag that is then washed with the work clothes. Wash hair and body thoroughly with soap and water. 12. WARNING: To reduce the risk of fir
Slower speed is compensated by the wider softened areas. Heat will also penetrate deeper. 2) As paint begins to blister and bubble, move gun slowly in a steady progression across the surface. Follow closely with a scraping knife (a 2-inch-wall scraper works best) to scrape the loosened paint. Preheat scraper as you are heating the paint surface. This increases the speed of paint stripping. a. Removal of paint by using heat is based on the fact that all organic paints soften at elevated temperatu
Fabrique aux Etats-Unis Hecho en EE.UU. Please read, understand and keep this manual for future reference Lire et bien comprendre les instructions contenues dans ce manuel et les conserver comme reference. Por favor lea, comprenda y guarde este manual para futura referencia. Description & Introduction The Masterflow® Heat Blower is a heavy-duty, industrial- quality heat blower suitable for continuous duty applications. It produces a high volume of hot air for demanding industrial applications. T
Fabrique aux Etats-Unis Hecho en EE.UU. Please read, understand and keep this manual for future reference Lire et bien comprendre les instructions contenues dans ce manuel et les conserver comme reference. Por favor lea, comprenda y guarde este manual para futura referencia. Description & Introduction The Master Heat Gun is a heavy-duty, Industrial-quality, general-purpose heat gun. High temperature Industrial jobs are done faster with this heat gun, because our MASTER models have higher power a
5349161 Users should independently evaluate the suitability of the product for their application. •Use to activate adhesives, bend plastics, dry filler material, etc. ® HEAT GUN •Compact light weight, easy-to-use design •Two heat settings 430°F and 840°F (221°C and 449°C) • Base provides built-in stand for hands free use •Convenient hanging loop • Easy grip handle •Protective switch guard •Multiple attachments available •Made in the USA Activate Adhesives Strip Paint ORDERING INFORMATION Model N
Description PH-1300 Proheat Variair Heat Gun PH-1300-1 Proheat Variair Heat Shrink System includes heat gun, stand and attachment (35292) PH-1300K Proheat Variair Heat Gun Kit, includes heat gun, 5 attachments (35309) and storage case TECHNICAL SPECIFICATIONS Voltage: 120V, 60Hz, 11A Output: 1300W maximum Temperature: Variable 130°F - 900°F (54°C - 482°C) Airflow Volume: Variable 6 - 15 CFM Airflow Velocity: 1425 - 3550 FPM Agency Approvals: UL, CUL Nozzle opening: .87” diameter Net Weight: 28 o