Login:
Sorted: Name ↑   Downloads   Rate   Size ↓  

Marvel Industries G-1700

downloaded: 14File size: 7 kb    Manafacture: Marvel Industries  
Category: Other Kitchen Appliances

Unsweat all tubes from the old compressor. Do not cut them off. 2. Place the new compressor into the ice machine, as shown. 3. This replacement compressor may be different than the original compressor and/or have slightly different tubing configurations. The suction line, discharge line, and/or suction service line at the compressor may need to be rerouted, when making this change-out. 4. Replace the compressor components (start relay, start capacitor, and run capacitor) with the new ones pro

Marvel Industries K00106

downloaded: 0File size: 9 kb    Manafacture: Marvel Industries  
Category: Other Kitchen Appliances

holes in the dispenser, as shown (adapters must be compressed on foam and level with dispenser). C. Fasten each adapter with the two screws provided in kit. D. Apply foam tape to the edge of adapters and on top of existing rear foam tape. 3. Ice machine installation: A. Position ice machine on dispenser. B. Proceed to ice machine installation manual for electrical and water hook-up and start-up procedure. Manitowoc Ice, Inc. 2110 South 26 Street, P.O. Box 1720, Manitowoc, WI 54221-1720 US

Marvel Industries K00114

downloaded: 8File size: 9 kb    Manafacture: Marvel Industries  
Category: Other Kitchen Appliances

Install, as shown. Manitowoc Ice, Inc. 2110 South 26 Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-7879 8009063 Rev. 12/09/97

Marvel Industries K00115

downloaded: 1File size: 9 kb    Manafacture: Marvel Industries  
Category: Other Kitchen Appliances

These louvers will not affect the operation of an ice machine with a remote condenser or a water-cooled condenser that previously did not have louvers in the right and left-hand side panel. 2. The air baffle must be installed on air-cooled machines only to prevent the condenser air from recirculating. Install, as shown. Manitowoc Ice, Inc. 2110 South 26 Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 9

Marvel Industries K00121

downloaded: 4File size: 9 kb    Manafacture: Marvel Industries  
Category: Other Kitchen Appliances

Note: C-970/980 only - remove the gasket from both sides of the bin. 2. Remove the #8 screws holding the current ice deflector. Save these screws, a total of 6 from a C-900/910 or a total of 12 from a C-970/980. 3. Remove the ice deflector. 4. Place the new ice deflector on the bin. 5. Fasten the ice deflector using the screws removed in step 2. If needed, use the two additional screws shipped with the kit. Note: C-970/980 only - seal the open screw holes in the bin sides with RTV sealant or

Marvel Industries K00127

downloaded: 0File size: 9 kb    Manafacture: Marvel Industries  
Category: Other Kitchen Appliances

The bin must be leveled before proceeding to step 2. 2. Installation of Adapter (see illustration): A. Locate right-hand and left-hand adapter panels. B. Using the adapter panels as templates, drill four 5/32” diameter holes for each adapter in bin. C. Fasten panels in place with the screws provided in kit. D. Apply foam tape, as shown. 3. Installation of Ice Machine: A. Position ice machine on bin. B. Proceed to ice machine installation instructions for electrical and water hook-up and

Marvel Industries K00047

downloaded: 1File size: 9 kb    Manafacture: Marvel Industries  
Category: Other Kitchen Appliances

The bin must be leveled before proceeding to step 2. 2. INSTALLATION OF ASAPTER: A. Remove four screws from bin used to hold hinges. B. Locate right-hand and left-hand adapter panels. C. Remove foam tape, which is under the adapter panels. D. Using panels as template, drill four holes, 5/32” diameter, in back of bin. E. Secure panels in place. F. Apply foam tape, as shown in Illustration 1. 3. INSTALLATION OF ICE MACHINE: A. Remove two screws from bottom of ice machine that are 16 1/2”

Marvel Industries K00160

downloaded: 2File size: 9 kb    Manafacture: Marvel Industries  
Category: Other Kitchen Appliances

Using the adapter as a template, drill two 5/32” (4 mm.) holes, .500” (12.7 mm.) deep maximum, in the back of the bin. Warning: Do not drill through interior liner. Attach with (2) 10-24 x .500” screws provided. B. Apply foam tape to the edge of the adapter opening as shown in the (A) position. Note: It is recommended to RTV intersections and along front inside edge of foam tape (see drawing) to prevent water tracking. C. Place the ice machine on the adapter. Secure it to the adapter as shown

Marvel Industries K00066

downloaded: 0File size: 10 kb    Manafacture: Marvel Industries  
Category: Other Kitchen Appliances

These louvers will not affect the operation of an ice machine with a remote condenser or a water-cooled condenser that previously did not have louvers in the right-hand side panel. 3. The air baffle must be installed on air-cooled machines only to prevent the condenser air from recirculating. Install, as shown: Manitowoc Ice, Inc. 2110 South 26 Street, P.O. Box 1720, Manitowoc, WI 54221-1720 USA Telephone 920-682-0161, Fax - Sales: 920-683-7589, Service/Parts: 920-683-7585, Other: 920-683-78

Marvel Industries K00022

downloaded: 1File size: 10 kb    Manafacture: Marvel Industries  
Category: Other Kitchen Appliances

The two deflectors should be installed end-to-end to make one continuous deflector. C. Apply foam tape to adapters and front and rear bin rail, as shown. D. Locate right-hand and left-hand adapter panels. E. Using the adapter panels as templates, drill four 5/32” diameter holes for each adapter in bin. F. Fasten panels in place with the screws provided in kit. 3. Installation of ice machine: A. Position ice machine on bin. B. Proceed to ice machine installation instructions for electrical





Category