The kits contain seven louvers plus one louver with two pre-drilled holes (eight total) and these instructions. INSTALLATION INSTRUCTIONS Step 1. Turn off the fireplace and allow it to cool before proceeding. Step 2. Slightly lift and pull the existing top louver assembly away from the fireplace. Step 3. Slightly lift up the bottom hinged panel to disengage the small hooks on ether side of the panel. Pull forward and lower the panel down to open. Remove the assembly from the fireplace by rem

Pull forward and lower the panel down to open. Remove the assembly from the fireplace by removing the hinge screw on each end of the assembly. Step 4. Working with one assembly at a time, remove the existing black louvers separating the brackets from the assemblies (see Figure 1). To ease the removal of the brackets, use a side bladed screwdriver and mallet to "tap" down the bend in each bracket finger (restore the bend by hand before reassembly). Replace the black louvers with the brass or bru

Then tilt top of door toward vertical position making sure that all Pins and Door Guides are inside Track. Finally, slide Top Pin along Top Retainer Clip until Top Pin snaps into Top Retainer Slot. Repeat procedure for left door. Top (Narrow) Door Guide (Wide) Door Guide Retainer Clip Bottom BottomRetainer Handle Clip Pin Figure 3 Figure 2 NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE ADJUSTMENT FOR DOOR ALIGNMENT ADJUSTMENT FOR DOOR ALIGNMENT If doors appear to close in correct position but do no

Insert the screws through the side panel holes and screw them into the pilot holes just drilled. Model Estate 48 Fireplaces Note:The Center Wedge Clip located inside the track in the center of the door frame indicates the bottom of the frame. It is important that the frame be installed with the correct side up to insure smooth operation of the doors. Step 1. Lay the frame face down on a clean, soft surface to avoid scratching the brass. Note the two Phillips Screws mounted to Tinnerman nuts on e

DO NOT SIT CLOSE TO THE GLASS. Tempered glass will break into small particles if it should shatter unexpectedly. If the glass breaks, particles of extremely hot glass could be discharged into the surrounding environment, thereby creating a risk of personal injury or fire. Observation of the above operating precautions and instructions will reduce the risk of personal injury or fire. Extreme temperature changes can cause breakage — do not build a hot fire and close the doors if the doors are cold

Back these screws out about an 1/8 of an inch. Step 3. Position the Estate 48 attachment bracket within the fireplace opening with their black faces forward and their slots engaged around the screws backed out in the previous step. Snug up two (2) screws on each side, DO NOT TIGHTEN. The attachment brackets must be allowed to move in the following step. Step 4. Remove the Phillips screw from the Tinnerman nuts in the door frame assembly. Position the frame within the opening and align the Tinner

Step 2. Position the frame in the fireplace opening on top of the door support bracket, centering left and right. Mark the fireplace at each hole in the side panels. Note:The frame is provided with two sets of holes allowing for near "Flush Face" installation and "Protruding" installations that may be particularly useful in certain finish applications. In most cases the door frame will not install completely flush with the appliance front face. The frame will usually protrude from the opening ap

Lennox's Symphony series Bi-Fold doors come standard with a decorator satin black finish and may be purchased in a polished brass finish designated by the -B suffix to the model/size number. Do not alter or modify these door assemblies or a fireplace malfunction or a fire hazard may result. These glass door assemblies have been tested and listed by Warnock Hersey Inc. PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE. GENERAL INFORMATION This door assembly consists of a right and left bi-fold glass

Take care not to scratch the glass surface. Do not use abrasive cleaners. CAUTION: THE CST-38 AND CPF-38 FIREPLACES MUST BE OPERATED WITH THE GLASS DOORS FULLY CLOSED. IMPORTANT These glass doors utilize tempered glass which is designed for use with high temperatures but can unexpectedly shatter. DO NOT SIT CLOSE TO THE GLASS. Tempered glass will break into small particles if it should shatter unexpectedly. If the glass breaks, particles of extremely hot glass could be discharged into the surrou

Additionally these doors are designed for use with the Merit Plus Series, Models CST-38 and CPF-38. Do not alter or modify these door assemblies or a fireplace malfunction or a fire hazard may result. Models 38ABF(BB/BS) have been tested and listed by Omni Test Laboratories, Inc. PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE. GENERAL INFORMATION This door assembly consists of a right and left glass panel assembly with the door handles factory mounted. There are no additional parts that are requ