Holding down the cue button changes the cue function to preview (allowing you to hear the music play at whatever tempo you adjusted to by holding the cue button down). Releasing the cue button returns you to the preset cue point. CUE/B REPEAT: After the cue point is memorized, pressing the CUE/B BUTTON (12) in the play mode, (the cue LED BLINKS yellow), repeats the section between the cue point and the point where the CUE/B BUTTON (12) was pressed (there will be a slight delay between the end an

When done press stop. 10. Upon completion, press the TRACK button to enter the Vtr1-8 (Vtr1-6 on the D12) screen. 11. Using the cursor button highlight 1a then using the value wheel, select virtual track 1h. Do the same for track 2a (set to 2h). 12. Set the pan pots for tracks 1 & 2 left and right respectively, and set the faders to unity (0dB). 13. Repeat steps 1-12 for every song that you wish to put to CD. Now we’re ready to burn tracks 1 and 2 to CD. Set Scene Read to OFF at this point,

If they are okay, check your amplifier or receiver. • If the CD skips, check the CD for dirt or scratches. Do not assume that the CD player is defective. Many CDs are recorded out of spec and will skip on most or all CD players. Before sending the unit in for repair, try playing a CD that you are sure plays properly. SPECIFICATIONS GENERAL: Type.................... Dual Mechanism Compact Disc Player w/wired remote Disc Type............................... Standard Compact discs (12 cm & 8 cm) Tim

6. Refloat the TONE ARM to ensure horizontal zero (0) balance. If zero balance has not been maintained, repeat counterweight steps 3 - 5. 7. After adjusting the horizontal zero (0) balance, turn the balanced COUNTERWEIGHT (7) counter clockwise until the cartridge manufacturer’s recommend stylus pressure appears on the STYLUS PRESSURE RING (10) where it meets the center line of the TONE ARM (5) rear shaft. ADJUSTING THE ANTI-SKATING CONTROL: Set the ANTI-SKATING CONTROL (11) to the same value as

PLAY/PAUSE: Each press of the PLAY/PAUSE BUTTON (5) causes the operation to change from play to pause or from pause back to play. See the CUE INSTRUCTIONS section for more information. TRACK SKIP: The TRACK SKIP BUTTONS (6) let you select the track to play. SEARCH JOG WHEEL: The SEARCH JOG WHEEL (7) is used to accurately position the disc at the point where you wish the track to start playing. This position on the track will be memorized as the CUE POINT. Each move of the SEARCH JOG WHEEL (7), i

standstill to 33 1/3 RPM Braking System........................................Electronic Brake (Solenoid) Wow and Flutter...................................................................0.02% WRMS* * This rating refers to the turntable assembly and platter only and excludes effects of records, cartridges or tonearms. Rumble........................................................................56 dB Unweighted TONEARM SECTION: Type...............................................Universal S-Sha

In play mode, pressing a CUE BUTTON will pause play and bring you to the CUE POINT when you can then press the play/pause button to play from the CUE POINT. SET CUE: Use the SET CUE (10) button to activate the DIRECT ACCESS BUTTONS to set a CUE POINT. See the CUE INSTRUCTIONS section for more information. DIRECT ACCESS BUTTONS: Use the DIRECT ACCESS BUTTONS (2) to select what track to play and to set a CUE POINT. See the CUE INSTRUCTIONS section for more information. SINGLE-AUTO CUE/CONTINUOUS:

Prior to use, we suggest that you carefully read all the instructions. Features • 4 Stereo Channels • State of the Art Cue Section • 1 Phono/Line Convertible, 2 Phono, 5 Line, and 3 Mic Inputs • Cut Feature for Low, Mid and High for each channel • Gain, High, Mid and Low tone controls for each channel • Talkover • Balanced and Unbalanced Master Outputs • Booth Output • Master Output Peak Hold LED Meters • Prefader Input Level Peak Hold LED Meters for each channel 5. On the rear panel are 1 stere

4. Den neuen Uberblender mit den Schrauben am Mischpult befestigen. 7. TAKTANZEIGEN: Jede Seite des CROSSFADER (22) ist mit einer eigenen Taktanzeige BEAT INDICATOR (21) ausgerustet. Diese leuchten beim Spitzenpegel der niedrigen Frequenz der zugewiesenen Quelle auf und erlauben visuellen Abgleich der Takte. 8. AUSGANGSREGELUNG: Der Verstarkerausgangspegel AMP OUT (39, 40) wird vom MASTER (32) und BALANCE (31) geregelt. Der Regler BOOTH (30) justiert den Pegel des BOOTH OUTPUT (41). EMPFEHLUNG:

Press the SET CUE BUTTON (15) (the LED will light). Use the DIRECT ACCESS (2) buttons to memorize the spot at which you want play to start, the CUE POINT, by selecting the proper track, minute, second and frame. Press CUE 1 to set the cue to CUE 1 (press CUE 2 if you wish to set the cue to CUE 2). You can do this in any mode, including PLAY MODE, so that you may cue a track while playing a track. SUGGESTION: To avoid confusion while setting cue points, keep the time display in ELAPSED TIME mode.