4. WARNING – to reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch the plug with wet hands. Assembly Instructions: 1. After opening the carton, please remove all parts and check against photograph on carton. If any parts are missing, please call Alltrade at 1-800-423-3598. 2. Close the drain valve on the bottom of the air tank by turning the valve clockwise until fully closed. 3. Attach the air hose to the compressor regulator valve. Use included Teflon t

Do not touch the plug with wet hands. Assembly Instructions: 1. After opening the carton, please remove all parts and check against photograph on carton. If any parts are missing, please call Alltrade at 1-800-423-3598. 2. Close the drain valve on the bottom of the air tank by turning the valve clockwise until fully closed. 3. Attach the air hose to the compressor regulator valve. Use included Teflon thread-sealing tape on the threads to make sure you have an airtight connection. Do not overtigh

If you encounter any problems or difficulties, please contact our Customer Service Department at: 1-310-522-9008 Por favor, guarde estas instrucciones para que le sirvan de referencia en el futuro. Si usted se encuentra con algun problema o dificultad, por favor, comuniquese con nuestro Departamento de Servicios para el Consumidor: 1-310-522-9008 2 3 2 GALLON AIR COMPRESSOR • Do not pull on power cord to disconnect it from the outlet. Keep cord away form heat, oil, and sharp edges. • NEVER move

The owner/operator shall retain product instructions for future reference. The owner and/or operator is responsible for maintenance, maintaining all decals or warning labels and while in use, maintaining the unit in good working order. If the owner and/or operator is not fluent in English, Spanish, or French, the product warnings and instructions shall be read and discussed with the operator's native language by the purchaser/owner or his designee. Make sure that the operator comprehends its con

Check valve stuck in open position. Replace check valve. DANGER—Do not disassemble the check valve with tank pressurized. Open tank petcock valve to allow air to escape from tank prior to servicing. Air leaks from safety relief valve: Possible defective safety relief valve. Operate safety relief valve manually by pulling on ring. If it still leaks, it should be replaced. Excessive tank pressure. Defective motor/pressure switch. Replace. Air leaks at pump: Blown gaskets. Replace blown gaskets and

• Where flammable gas vapors or materials may be present. • Where air temperatures fall below 32.F or exceed 104.F. • Where extremely dirty air or water could be drawn into the air compressor. SERIOUS INJURY OR DEATH MAY OCCUR IF ELECTRICAL SPARKS FROM MOTOR AND PRESSURE SWITCH COME IN CONTACT WITH FLAMMABLE VAPORS, COMBUSTIBLE DUST, GASES OR OTHER COMBUSTIBLE MATERIALS. WHEN USING THE AIR COMPRESSOR FOR SPRAYING PAINT, PLACE THE AIR COMPRESSOR AS FAR AWAY FROM THE WORK AREA AS POSSIBLE, USING E

If you must use an extension cord, it should be plugged into a GFCI found in circuit boxes or protected receptacles. Use only UL listed 3-wire extension cords that have a 3-blade grounding plug and a 3-slot receptacle that will accept the plug on the product. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. Refer to the guide below for minimum gauge required for extension cords. Use only

This warranty shall be null and void if the product or any component thereof is modified or altered. This warranty does not apply to any other product and/or component thereof manufactured or distributed by Alltrade, and does not apply to products and/or components thereof designed, manufactured and/or assembled by others, for which Alltrade makes no warranties whatsoever. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. Warranty Performance By purchasing the produ

3. Place a suitable oil drain pan below oil drain plug (see Fig. 4). 11 Weekly: • Inspect and clean air filter. • Clean breather holes on oil fill plug. Monthly: • Check for air leaks.+ • Check safety relief valve. Six months or 200 operating hours:* • Change compressor oil. Use only SAE 30 weight non-detergent air compressor oil. • Replace oil more frequently when used in dusty operating environments. 4. Remove oil fill breather plug to allow air to enter crankcase. 5. Remove oil drain plug. 6.

• Make sure the WCE moves up and down without sticking or binding. If sticking or binding occurs, discontinue use of the nailer/stapler until proper service and/or repairs are performed • Connect the air supply to the nailer/stapler. • Press the WCE against the work piece without pulling the trigger. The nailer/stapler must not operate. • Hold the nailer/stapler clear of the work piece. The work contact element should return to its original down position. Pull the trigger. The nailer/stapler mus