17, located in the machine base. Fig. 17 OPERATING CONTROLS AND ADJUSTMENTS STARTING AND STOPPING DRILL PRESS The switch (A) Fig. 18, is located on the front of the drillpress head. To turn the drill press “ON” move the switch up to the “ON” position. To turn the drill press “OFF” move the switch down to the “OFF” position. 10 R Q Fig. 15 S T Fig. 16 A A Fig. 18 LOCKING SWITCH IN THE “OFF” POSITION IMPORTANT: When the machine is not in use, the switchshould be locked in the “OFF” position to pre

For Parts, Service, Warranty or other Assistance, please call 1-800-223-7278 (In Canada call 1-800-463-3582). FRANCAIS : PAGE 34 10" Bench Drill Pre s s (Model SM300) PART NO. 638517-00 10-30-05 Copyright © 2005 Delta Machinery ESPANOL: PAGINA 18 To learn more about DELTA MACHINERYvisit our website at: For Parts, Service, Warranty or other Assistance, please call 1-800-223-7278 (In Canada call 1-800-463-3582). FRANCAIS : PAGE 34 GENERAL SAFETY RULES Woodworking can be dangerous if safe and prope

Box 168 803-271-9000 Myrtle Beach 29577 Coastal Elec. & Rewinding 718 8th Avenue N. 803-448-3586 Spartanburg 29302 Cash Supply 113 Country Club Rd 803-585-9326 SOUTH DAKOTA Rapid City 57702 Stan Houston Equipment Co. 1210 Deadwood Avenue 605-348-1155 Sioux Falls 57702 Sian Houston Equip. Co 501 S Marrion Road 605-336-3727 TENNESSEE Chattanooga 37412 F & D Tool Service and Supply 4121 Ringgold Road 615-698-6454 Clarksville 37042 Opa's Shop 312 Pine Mountain Road 615-647-5842 Jackso

434-08-651-0006 ©Delta International Machinery Corp. 1997 12" Variable Speed Wood Lathe (46-700 Bench Model) (46-701 Floor Model) INSTRUCTION MANUAL TABLE OF CONTENTS SAFETY RULES...............................................................................................................................................................3 ADDITIONAL SAFETY RULES FOR WOOD LATHES...................................................................................................4 UNPACKING AN

II is equipped with a brass plug on one end and a comfortable knob on the other. IMPORTANT: NEVER DRIVE THE WORKPIECE INTO THE SPUR CENTER WHEN IT IS MOUNTED IN THE HEADSTOCK. Instructions on setting the spur center into the workpiece are found in the “OPERATION” section of this manual. Fig. 29 TAILSTOCK LIVE CENTER The tailstock live center (A) Fig. 31, supplied with your lathe, is equipped with a No. 2 Morse Taper shank and is inserted into the tailstock spindle (B), as shown. To remove the

Nonslip footwear isrecommended. Wear protective hair covering to containlong hair. 4. DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT. The use of power tools in damp or wetlocations or in rain can cause shock or electrocution. Keep your work area well-lit to prevent tripping or placingarms, hands, and fingers in danger. 5. M A I N TAIN A L L TOOLS AND MACHINES IN PEAK CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accesso

When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersizedcord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. C shows the correct gauge touse depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavierthe cord. MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STAT I O N A RY ELECTRIC MACHINES A m p e re R a t i n g Vo l t s Total Length of Cor

and Model No. plate is attached to the top surface of the frame casting. This plate can be seen by removing the front guard and looking behind the left edge of the upper blade wheel. Locate this plate and record the Serial No. and Model No. in your manual for futur^ reference. SERIAL NO. _ MODEL NO__ PART NO. 1088294 DATED 5-25-77 SAFETY RULES FOR ALL TOOLS As with all power tools there is a certain amount of hazard involved with the operator and his use of the tool. Using the tool with th

Current models have stamped sheet metal blower housings. D - When screw requires servicing install at 100 inch lbs 10 REPLACEMENT PARTS 50-185 BAG ASSEMBLY ----------- (OPTIONAL FOR 50-180 & 50-181 - STANDARD FOR 50-182) REF № PART NUMBER 50-185 1 50-188 2 410-06-027-00001 3 410-06-105-0001 4 50-195 OESCRIPTIQN DRUM MOUNTED DUST BAG, CONST OF: HOSE, INCL; CLAMP - 6" HOSE SLEEVE DUSTBAG NOT SHOWN ASSEMBLED NOTE: THE NECK OF THE BAG MUST BE CLAMPED TO THE DRUM USING A STANDARD 55

In a severe dirty operation, the blower impeller should be cleaned with a wire brush to prevent an accumulation of foreign matter that could result in blower unbalance After cleaning impeller, inspect for possible cracks or excessive wear, which can cause unbalance. DO NOT USE AN IMPELLER THAT IS CRACKED OR EXCESSIVELY WORN; REPLACE IT WITH A NEW IMPELLER. MOTOR MAINTENANCE: Removing dust and dirt: Blow off motor with low pressure air to remove dust or dirt. Air pressure above 50 P.S.I. shou