Reinforce the structure as required before installing the component. 1. Level wall plate (C) and mark locations of pilot holes. 2. Drill 7/32" (5.5mm) diameter pilot holes into wood studs. 3. Using 1/2" (12.7mm) wrench, install screws (Y) through flat washers (Z), wall plate (C), into wood studs. 4. Open both display latches. 3 1 1 X4 2 X4 (Y, Z) X4 4 X2 1/2" (12.7mm) 7/32" (5.5mm) C C iCMPFM1S/iCMPFM1B Installation Instructions 12 INSTALL BRACKETS TO DISPLAY 1. Lay display face down on protecti
1. Nivele la placa para montaje en pared (C) y marque la ubicacion de los orificios piloto. 2. Perfore orificios piloto de 5,5 mm (7/32") de diametro en los listones de madera. 3. Utilice una llave de 12,7 mm (.") para introducir los tornillos (Y) en los listones de madera a traves de las arandelas planas (Z) y la placa para montaje en pared (C). 4. Abra ambas trabas de la pantalla. 3 1 1 X4 2 X4 (Y, Z) X4 4 X2 12,7 mm (1/2") 5,5 mm (7/32") C C Installation Instructions iCMPFM1S/iCMPFM1B 15 INST
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio or television communications. However, there is no guarantee that the
The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. Chief® is a registered trademark of Milestone AV Technologies. All rights reserved. IMPORTANT SAFETY INSTRUCTIONS WARNING alerts you to the possibility of s
(The doors should travel to the fully closed position) 7 8 From Dimmer Module Top of 24VDC Input Cabinet Front of Cabinet Installation Instructions CM6DH SERIES Activator Activator Button Figure 10 5. Press the "Open Door" button on the Remote Control. NOTE: If a different travel distance is required see "Door Travel Adjustment below. ADJUSTMENTS Adjust Door Travel Distance To adjust door travel distance: 1. Press and hold the activator button on the front of the motor box for 13 seconds. The St
The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document. IMPORTANT WARNINGS AND CAUTIONS! WARNING: A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions. CAUTION:
Refer to communication equipment manufacturer’s specifications for minimum spacings. • This Cabinet System is for use with ITE or Audio/Video equipment only. CMA470, CMA471 Installation Instructions 4 DIMENSIONS 2X 7.00 177.800 13.97 354.858 4X .44 11.113 1.375 34.925 13.71 ID 348.360 2X 7.81 198.438 2X 4.76 120.924 4X 11.113 134.564 6.34 ID 161.068 GROUNDING SCREW CMA-470 Measurements in: [millimeters] inches 2X 7.00 177.800 O 1.38 34.925 13.97 354.858 4X .44 11.113 13.69 ID 347.616 6.91 175.41
CMA accessories similar. 3. Secure lid to box (A) with two screws (D) (See Figure 2). Tighten securely. Figure 2 4. Connect ground wire to grounding screw. (See Figure 3) Figure 3 NOTE: Knockouts are provided for ease of installation. Any open knockout needs to be plugged, using parts (B) or (C). Additional 1/2" (B) or 1" (C) plugs may be purchased at a local store, if needed. 2 (D) x4 3 (D) x 2 Grounding Screw (CMA-470 shown) Installation Instructions CMA470, CMA471 MANUFACTURERS DECLARATION OF
The wall arm on the CTA-225 is 25.2” in length from the wall mount, providing ample room to install and position a small or large TV/Monitor. CTA-225 Dual Stud Wall Arm BEFORE YOU BEGIN • CAUTION: To prevent damage to your equipment, which could affect or void the Factory warranty, thoroughly study all instructions and illustrations before you begin to install the CTA-225. Pay particular attention to the Warnings and Cautions in this document. • If you have any questions about this installation,
WARNING The combined weight of the TV/monitor and all attached components and equipment placed on a Chief Wall Plate must not exceed 150 lbs. (68.0 kg), the maximum support weight of the CTA-2536. WARNING Watch for pinch points. Do not put your fingers between movable parts. CAUTION Check the unit for shipping damage before you begin the installation. PARTS 10 40 30 50 60 20 70 Figure 1. CTA-2536 Parts Installation Instructions CTA-2536 CONTENTS PARTS ............................................