Simple push-button action delivers a shot of water which is immediately converted into steam. Because the amount of steam is consistent, it removes the guesswork and produces a uniform finished product from one operator to the next. This manual provides the safety, installation and operating procedures for the Deluxe Food Warmer (steamer). We recommend that all information contained in this manual be read prior to installing and operating the unit. Your Deluxe Food Warmer (steamer) is manufactur
PRESS ‘ENTER’ TO CONTINUE message. Press Enter or wait and the system will prompt you for the password again. 5. The system displays the TURN OFF POWER, WAIT 10 SEC, RESTORE POWER message. Unplug the power cord and wait for ten (10) seconds or more, and then plug the cord in again. 6. The system then cycles through initialization displays and prompts you to set the Date and Time. Follow the instructions in the Set Date/Time Modes section of this manual. The system can then be re-programmed as de
Steam coming out around top covers or sides. Generator Cover’s wingnut is loose. Tighten wingnut. Generator Cover is warped. Replace Generator Cover. 20 P/N 1010699 Rev. M 12/06 MIRACLE STEAMER TROUBLESHOOTING (continued) Problem Possible Cause Corrective Action Unit floods overnight and/or continues to steam even when in idle mode. Solenoid Valve is leaking due to debris trapped inside the plunger (MS-250/255). Attempt to flush the debris out of the valve by rapidly operating the unit on a numb
Nickel. MAINTENANCE (continued) Replacing the Optional Roller Tensioners 1. Remove the acorn nuts and old roller Tensioner Assembly (Figure 12). 2. Replace Tensioner Assembly, and reassemble. 3. Make sure the spacers are placed inside the Tensioner arm. The spacers are smaller than the holes to allow the Tensioner to pivot freely. Weld Screws Acorn Nuts Tensioner Assy. Spacers Teflon Tape Figure 12. Replacing Roller Tensioner Assy. Figure 14. Measuring Roller Tensioner Replacing the Spring Tensi
Acorn Nuts Weld Screws Figure 9. Replacing Spring Tensioner Assy. 4. Make sure the spacers are placed inside the tensioner arm. The spacers are smaller than the holes to allow the tensioner to pivot freely. Replacing Conveyor Motor and Fan Blade NOTE: A small amount of Loctite (Blue & Red) is required for proper gear motor installation. 1. Remove control cover. 2. Disconnect the motor wires and remove the drive motor and drive motor bracket (Figure 10). Discard the 8-32 x 5/16” mounting bracket
To reset this thermostat, allow sufficient time (10-15 minutes) for the unit to cool down, then fully depress the reset button located at the rear of the unit (Figure 5). If the unit requires continuous resetting, contact your Roundup authorized service agency. CONVEYOR INTERLOCK SWITCH A conveyor interlock switch is located on top of the unit under the heat shield (Figure 4). The conveyors will not rotate unless the heat shield is in place and interlock switch is activated (depressed). Bun Thic
If low or zero voltage, replace power cord. If voltage is correct, check for correct voltage out of rocker switch. If low or no voltage, replace rocker switch. Wiring problem. Check all electrical connections for burns, discoloration or arcing. Replace all connections or components with damaged terminals. Replace all damaged wiring with the same (or higher) rated wire. Platen inoperative. To check platen: Use an Ohm meter to test resistance of the platen heater (disconnect 1 wire to isolate heat
to clear/reset this record, press both the uP and DOWN arrow buttons simultaneously (before turning the unit Off) and the display will show 33°f - indicating that record has been cleared - and then turn the unit Off. P/N 1010745 Rev. g 03/06 17 Variety Steamer maIntenance (continued) technical theory of Operation When the Rocker switch (power On/Off) is ON, line voltage flows to the primary side of the step down transformer. the transformer’s secondary side supplies 12 and 24 Vac to the control
this will ensure proper steaming characteristics by creating a thin layer of mineral deposits on the casting. caUtIOn all electrical connections must be in accordance with local electrical codes and any other applicable codes. warnInG electrIcal sHOcK HazarD. faIlUre tO fOllOw tHe InstrUctIOns In tHIs manUal cOUlD resUlt In serIOUs InjUrY Or DeatH. • electrical ground is required on this appliance. • Do not modify the power supply cord plug. If it does not fit the outlet, have a proper outlet in
Monthly Your Miracle Steamer utilizes an open steam generator. Water sprayed onto the generator surface flashes into steam immediately, but the minerals in the water do not steam, they stay on the generator surface. A small amount of mineral deposits are needed for proper operation, but a build-up of excessive mineral deposits causes poor steaming efficiency, excessive moisture (wet steam) and will eventually severely retard the steaming action completely. Cleaning Steam Generator 1. Turn the ro