Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. T-15 TORX bit driver 4. Razor knife or similar 5. Awl or similar tool 6. 1/4” hex socket bit 7. 18 GA wire 4' 8. Audiovox Series 640/650 Video Module

Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other componentry above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. T-45 TORX bit driver 4. Razor knife or similar 5. Awl or similar tool 6. 1/4” hex socket bit 7. 7/64" drill bit 8. Small chisel 9. Audiovox Series 64

dome light area. Align the front mounting tabs with the openings in the metal inner roof openings previously used to support the rear pod retainers. Slide bracket to rear of vehicle until flange contacts rear edge of recessed area. See Figure 7. FIGURE 7 7. Secure bracket to sheetmetal frame using four (4) # 8 x 3/4" HWH TEKS screws ( item 1 pg 2 ). Secure O.E.M. ground wire (if applicable) using one of the screws. See Figure 8. FIGURE 8 6 8. If vehicle is equipped with an electronic compass, un

Failure to do so may cause damage to console or installed components. Figure 16 2. Raise overhead console into approximate position and connect wiring to O.E. components. 3. Loosely fit console against headliner. Check that console is centered in vehicle and matches all contours of headliner. While supporting console in mounting position, loosely install using two (2) 6-32 X 3/4" screws (item 10 pg 2) through the smaller holes in bracket on console into threaded clips on mounting bracket. See Fi

Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. Awl or similar tool 4. Digital Volt Meter 5. 18 GA wire 9' 6. Rubbing Alcohol 7. 5/16” Hex Socket Bit 8. Razor knife or similar 9. Pencil or equivalent 10. Measuring tape 11. Masking tape 12. Audiovox Video Module NOT FOR VEHICLES EQUIPPED WITH SUN ROOF. 128-6067 Text Box: Feb. 13,2001 Printed in the U.S.A Text Box: INSTALLATION INSTRUCTION # 44-00

Special tools and equipment, as well as specialized handling and care of product during installation, may be required. Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other components above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. Razor Knife or Similar 4. Di

NEVER INSTALL THE MONITOR IN A PLACE WITHIN THE DRIVER'S VIEW. THIS IS NOT ONLY DANGEROUS, BUT IT IS ALSO ILLEGAL. 4) Once the mounting location of the monitor has been determined, there may be additional preparation work necessary, depending on the vehicle structure and installation method. Some of the steps that may be required are: A) Removal of the vehicle's dome light. B) The headliner may need to be trimmed. 8 MOUNTING THE VOD80 Figure 2 NOTE: Two of the mounting holes are located under th

• Repeat All- repeats the disc that is playing. • Off As you toggle through the options, the repeat option changes. The selected repeat option loops repeatedly until it is turned off. K. PLAYING MP3 DISCS MP3 is a digital audio format. An audio CD-quality song is compressed into the MP3 format with no significant loss of audio quality. CD-R / RW discs that have been encoded in MP3 format are compatible with this device. Insert a MP3 Disc, the DVD player will initialize the disc and the directory

Special tools and equipment, as well as specialized handling and care of product during installation, may be required. Before beginning this installation, carefully read through the following instructions. Use extreme care when cutting headliner material. Check for wiring or other components above headliner material. Cut only where indicated. Materials/ Tools required for this installation: 1. #2 Phillips screwdriver 2. Powered screwdriver or drill with adapter 3. Razor Knife or Similar 4. Di

2 I. PREPARATION OF VEHICLE INTERIOR 1. Remove the O.E.M. console mounted to inner roof of vehicle. Remove and discard dome light cover to gain access to (2) two #8 x 3/4" screws. Retain screws. Remove and retain (1) one #8 x 1 1/2" screw located in front of console near rear view mirror. See Figure 1. 2. Lower console and disconnect wiring at (2) two locations. Lay console on workbench for modification later. See Figure 2. 3. Using rear edge of opening in headliner, carefully trim headliner as