Align dimple of top pole section (4) into trough of middle pole section (5) as shown. IMPORTANT! HOLE DIMPLE middle pole THE IDENTIFICATION STICKER IS LOCATED 5" FROM THE END OF THE POLE. WHEN PROPERLY POUNDED TOGETHER, THE POLE SECTIONS SHOULD HAVE A 3-1/2" MINIMUM OVERLAP, LEAVING 11/ 2" BETWEEN THE OVERLAPPING POLE AND THE IDENTIFICATION STICKER. CAUTION! 5" middle pole 1-1/2" ID STICKER 14 ID# M661134 03/06 5. 5. Bounce top and middle pole assembly (4 and 5) onto bottom pole section (6) usin

Introduzca el perno en T (42) en el soporte del borde (41). Asegure los soportes del tablero (25) y el soporte del borde (41) en el respaldo con los pernos (15 y 26) y las tuercas (8). 25 8 8 8 8 24 22 30 30 25 8 4. 5. 42 41 15 15 26 26 41 27 22 SECTION C: ASSEMBLE THE ELEVATOR SYSTEM and BACKBOARD SECTION C: MONTAGE DU SYSTEME ELEVATEUR ET DU PANNEAU BAUABSCHNITT C: ZUSAMMENBAU VON VERLANGERUNGSVORRICHTUNG UND KORBWAND SECCION C: MONTAJE DEL SISTEMA DEL ELEVADOR Y EL RESPALDO This is what your

Serious injury could occur if teeth/face come in contact with backboard, rim or net. • During play, do not wear jewelry (rings, watches, necklaces, etc.). Objects may entangle in net. • Check system before each use for loose hardware, excessive wear and signs corrosion and repair before use. • Never play on damaged equipment. • See instruction manual for proper installation and maintenance. Read and understand warnings listed below before using this product. Failure to follow these warnings may

4 5 6 WOOD SCRAP (NOT SUPPLIED) POLE SECTIONS SHOULD HAVE A 3-1/2" (9 CM) MINIMUM OVERLAP. NOTE: 5. P/N 21495407 08/05 10 6. Install rod (7) through holes in bottom pole section (6) and eyebolt (8). 7 4 8 6 5 7. Insert pole assembly into tank assembly as shown. 6 WARNING! 7 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR 8 PROPERTY DAMAGE. IMPORTANT!: DO NOT OVER TIGHTEN 8. Carefully place unit on its side. Secure pole bottom (6) to ta

Test fit large bolts into large holes of elevator tubes, backboard brackets and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. AVANT DE COMMENCER ! Pour garantir l'utilisation optimale du panneau, les composants du systeme elevateur et la visserie doivent etre bien ajustes (serres). A titre d'essai, inserez les gros boulons dans les gros trous des tubes du systeme elevateur, des supports du panneau et des plaques triangulaires. Bas

Paint/finish, components attached to the bicycle/ frameset such as front forks, wheels, drive train, brakes, seatpost, handlebar and stem or any suspension related parts or components are covered under the limited one (1) year warranty. This warranty is void if the bicycle or frameset was not purchased new from or not properly assembled by an authorized Specialized dealer. LIMITED ONE (1) YEAR WARRANTY ON COMPLETE BICYCLE Subject to the following limitations, terms and conditions, Specialized wa

28 26 16 P/N 214953C 12/03 SECTION B: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: HUFFYSPORTS TOOLS REQUIRED FOR THIS SECTION HARDWARE USED IN THIS SECTION (not actual size) (2) 1/2”, (2) 9/16" AND (2) 3/4" Wrenches 9/16”1/2” AND/OR (2) Socket Wrenches and Sockets Item #21 Item #47 Item #48 Item #37 Item #38 Item #44 Item #55 Item #16 Item #50 Item #35 Item #39 Item #56 Item #203/4” 17 12/03 P/N 214953C Install spacers (36) onto backboard brackets

x .5 O.D. x 1.8 Long 37 1 240017 Bolt, Hex Head, 1/4-20 x 2-1/4 Long 38 6 206311 Spacer, Plastic, .530 I.D. x .50 Long 39 7 206340 Locknut, Hex Head, 1/2-13 2 904820 Elevator Tube, Lower-Long 41 1 204838 Spring 42 1 Rim 43 2 904808 Elevator Tube, Upper-Short 44 4 201651 Spacer, 1/4 Long x 1/2 O.D. 45 2 900867 Plate, Triangle, (Black) 46 1 202814 Cap, Pole Top 47 6 206244 Bolt, Hex, 1/2-13 x 8 Long 48 1 204870 Bolt, Hex, 1/2-13 x 3-1/2 Long 49 2 203617 Plug Cap 12 201219 Smart Clip, Net Holder, 5

Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system. IMPORTANT! Remove all contents from boxes. Be sure to check inside pole sections; hardware and additional parts are packed inside. 4 P/N 211689C 05/03 Get to know the basic parts of your basketball system..... FRONT BACK TOP POLE MIDDLE POLE FRONT COVER RIM BOTTOM POLE BASE STRUTS ELEVATOR ASSEMBLY BACKBOARD WHEEL CARRIAGE ASSEMBLY 5 05/03 P/N 211689C Item Qty Part No Descript

13. SIDE OF WHEEL WITH LONGER PLASTIC AXLE NEEDS TO FACE THE WHEEL BRACKET. IMPORTANT!: TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! Install wheels (27) onto axle (28) and wheel bracket (25) with push caps (29) as shown. IMPORTANT!: DO NOT OVER TIGHTEN 14. 29 27 28 25 27 29 21 30 20 8 Carefully reposition entire assembly as shown: 12. 13. SIDE OF WHEEL WITH LONGER PLASTIC AXLE NEEDS TO FACE THE WHEEL BRACKE