Please Note: You may need to push out on the center panel and arched panel while pushing down on the platform. * insert the stair pegs into the middle holes on the arched pane) and center panel. Helpful Hint: )n the stairs position, the ladder peg bar rests on the ground. • To secure the platform: - Align the screw holes in the center panel and platform. You may need to slightly adjust the position of the platform to align the holes. Helpful Hint: To make sure the screw holes are aligned,

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Fasteners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Assembly Tip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 Decoration . . . . . . . . . . . . . . . . .

90 ASSEMBLYASSEMBLY ASSEMBLYASSEMBLY Straps SIDE VIEW STEP 79 • Remove the fabric from the straps on each side of the chute (there are five on each side). Throw the fabric away. • Wrap the straps on each side of the chute around an adjacent loop in the net and fasten. 91 Straps BACK VIEW Straps BACK VIEW STEP 80 • Remove the fabric from the straps. Throw the fabric away. • Wrap the straps on the top, left side of the chute around the wires and the tube. Fasten the straps. 92 ASSEMBLYASSEMBLY Str

• Please keep this instruction sheet for future reference, as it contains important information. • Requires three button cell (LR44) batteries for operation (included). • Tool required for battery removal: Phillips screwdriver (not included). ICES-003 This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interferen

Tool needed for assembly: Phillips screwdriver (not included).Tool needed for assembly: Phillips screwdriver (not included). Water or sand is needed to fill the bases (not included).Water or sand is needed to fill the bases (not included). IMPORTANT!IMPORTANT! Backboard height should be adjusted only by an adult.Backboard height should be adjusted only by an adult. M5726M5726 1. Basketball 2. Football 3. Soccer 4. Baseball 5. Hockey Owner's Manual with Assembly Instructionswith Assembly Instruct

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can

Adult assembly is required. Tool required for battery replacement: Phillips screwdriver (not included). 1 Overhead Gym Tummy-Time play 2 H8268 Instructions Playful Puppy Gym Please keep this instruction sheet for future reference, as it contains important information. Musical panda requires three alkaline (LR44) button cell batteries (included). Adult assembly is required. Tool required for battery replacement: Phillips screwdriver (not included). 1 Overhead Gym Tummy-Time play 2 Parts To preven

• Pull on the ball return to be sure all six ends are fastened to the rim. 3 Assembly Assembly 4 2 Side Edge Side Edge3 5 1 Proper label application will help to keep the label looking its best! • Make sure the area where the label will be applied is clean and dry. Wipe the backboard with a clean, soft, dry cloth to remove any dust or oils. • For best results, avoid applying the label more than once. • Peel the backing from one half of the label. Do not remove all of the backing! • Align the sid

Hint: For easier assembly, apply liquid soap or rub a candle or bar soap around the bottom of the upper post (especially on the corners) and the inside of the large square opening. If assembling inside, place a tarp under the base to protect the floor surface. • Insert the upper post into the large square opening in the base and, using a circular motion, push it all the way down. 4 56• Hook the rectangular tab on each side of the rim to the upper post, as shown. • Rotate the rim down until it sn