Observe all normal safety precautions related to avoiding electric shock. 1. Know your machine. Read this manual carefully. Learn the machine’s applications and limitations, as well as specific potential hazards peculiar to it. 2. Ground all machines. This machine is “Double Insulated,” meaning that all outside metal parts are insulated from electrical power. Double Insulated tools are equipped with a polarized plug. This plug will fit in a polarized outlet only one way. If the plug does not fit

Do not wear loose clothing, dangling objects, or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts. Air vents often cover moving parts and should be avoided. • Use safety apparel and equipment. Use safety goggles or safety glasses with side shields which comply with current national standards, or when needed, a face shield. Use as dust mask in dusty work conditions. This applies to all persons in the work area.

Table 1 shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. Table 1: Minimum gage for cord Ampere Rating Volts Total length of cord in feet 120 V 25 ft. 50 ft. 100 ft. 150 ft. More Than Not More Than AWG 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 Not Recommended SPECIFIC SAFETY RULES USB005-3 DO NOT let comfort or familiarity with product (gained from rep

1 2 3 9523NBH 1 2 3 9523NBH Wheel guard 2. Bearing box 3. Screw 001060 Installing or removing wheel guard CAUTION: • When using a depressed center grinding wheel/Multidisc, flex wheel, wire wheel brush or cut-off wheel, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator. Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard around 180 degrees. Be sure

Facsimile No: (714) 522-8133 Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste Paste FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ALABAMA COLORADO KENTUCKY NEW MEXICO PUERTO RICO 2365 Pelham Parkway 11839 E. 51st Ave. 1215 S. Hurstbourne Parkway 5805 Menaul Blvd. NE 200 Guayama St. Pelham, AL 35124 Denver, CO 80239-2709 Louisville, KY 40222 Albuquerque, NM 87110 Hato Rey, PR 00917 (205) 620-1791 (303)

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. SPECIFICATIONS Model 9526PBH 9527PB 9528PB No load speed (RPM) 10,000/min 10,000/min 10,000/min Overall length 275 mm (10-7/8”) 275 mm (10-7/8”) 275 mm (10-7/8”) Net weight 1.5 kg (3.3 lbs) 1.5 kg (3.3 lbs) 1.5 kg (3.3 lbs) Spindle thread M10 x 1.25 5/8” 5/8” • Manufacturer reserves the right to change specifications without notice. • Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and un

Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: Home Center Other ( Hardware/Lumber Store Tool Distributor Industrial Supply Construction Supply 2. Use of the product is intended for: Construction Trade Industrial Maintenance Home Maintenance Hobby Other ( ) 5. Any comments: 3. How did you learn about this product: ) Magazine Radio From Dealer Exhibition Newspaper

To remove the disc, follow the installation procedure in reverse. OPERATION WARNING: • It should never be necessary to force the tool. The weight of the tool applies adequate pressure. Forcing and excessive pressure could cause dangerous wheel breakage. • ALWAYS replace wheel if tool is dropped while grinding. • NEVER bang or hit grinding disc or wheel onto work. • Avoid bouncing and snagging the wheel, especially when working corners, sharp edges etc. This can cause loss of control and kickback

7. Use only flanges specified for this tool. 8. Be careful not to damage the spindle, the flange (especially the installing surface) or the lock nut. Damage to these parts could result in wheel breakage. 9. NEVER use tool with wood cutting blades or other sawblades. Such blades when used on a grinder frequently kick and cause loss of control leading to personal injury. 10. Hold the tool firmly. 11. Keep hands away from rotating parts. 12. Make sure cord is clear of wheel. Do not wrap cord around

Higher speed is obtained when the dial is turned in the direction of number 5. And lower speed is obtained when it is turned in the direction of number 1. Refer to the table below for the relationship between the number settings on the dial and the approximate rotating speed. RPM (/min) 1 2,800 | | 2 4,000 | | 3 6,500 | | 4 9,000 | | 5 10,500 CAUTION: • If the tool is operated continuously at low speeds for a long time, the motor will get overloaded and heated up. • The speed adjusting dial can