Nonslip footwear isrecommended. Wear protective hair covering to containlong hair. 4. DO NOT USE THE MACHINE IN A DANGEROUS ENVIRONMENT. The use of power tools in damp or wetlocations or in rain can cause shock or electrocution. Keep your work area well-lit to prevent tripping or placingarms, hands, and fingers in danger. 5. M A I N TAIN A L L TOOLS AND MACHINES IN PEAK CONDITION. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accesso

When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersizedcord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. C shows the correct gauge touse depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavierthe cord. MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STAT I O N A RY ELECTRIC MACHINES A m p e re R a t i n g Vo l t s Total Length of Cor

22, is located on the sander base. To turn the sander “ON” move the switch up to the “ON” position. To turn the sander “OFF” move the switch down to the “OFF” position. A Fig. 22 11 LOCKING SWITCH IN THE “OFF” POSITION IMPORTANT: When the machine is not in use, the switch should be locked in the “OFF” position to prevent unauthorized use. This can be done by grasping the switch toggle (B) Fig. 23, and pulling it out of the switch as shown. With the switch toggle (B) removed, the switch will not

1/2" Socket Wrench 18. Spindle Adapter 19. Dust Bag 17 167 15 UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the rust-preventative oil from unpainted surfaces using a soft cloth moistened with mineral spirits, paint thinner or denatured alcohol. Do not use highly volatile solvents such as gasoline, naphtha, acetone or lacquer thinner for cleaning your machine. After cleaning, cover the unpainted surfaces with a good quality househol

10-24x3/8" Pan Head Screw (2) 10. M8.4 Flat Washer (1) 11. 3/16" Flat Washer (2) Fig. 1 1 2 3 4 5 6 7 8 9 12 13 5 ASSEMBLY WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. BELT SANDER TABLE 1. DISCONNECT MACHINE FROM POWER SOURCE. 2. Locate the M8x1.25x30mm hex head screw (A) Fig. 2, M8.4 flat washer (B), and table locking handle assembly (C), (D), (E) and (F). NOTE: T

We suggest wiping any FI®» 1 excessive leakage of oil from the sides of the base casting to avoid the possibility of any grit entering the porous bronze bushings. OPTIONAL MOTORS N®, '■ HJP. Hearings Speed Volts 82-133 % Sleeve 1725 115 62-134 _ % Ball 1725 115 62-142 m Ball 1725 115 ACCESSORIES Miter Gauge No. 31-304 For use with 31 -200 81## 'Disc Sander. Sanding Discs No. 46-101 Coarse (40 grit) No. 46-102 Medium (80 grit) Pkg. of 12, 8%" diameter, garnet. Requires disc adhesive

416-01-651-0001 Dated 10-20-78 31-200 8V2" DISC SANDER The 81/a" Disc Sander permits straight, angular, curved and convex surfaces to be finished accurately. For circular, band and scroll sawed work, beveling edges and ends of square stock and rounding corners, it is ideal. It can be used for finishing wood, plastics, non-metals and metals in the home workshop. TILTING THE TABLE The table of disc sander can be tilted 45 degrees down and 30 degrees up. To make this adjustment, 'loosen the han

3. Loosen set screw (F) Fig. 34, and insert support bar (E) and table assembly (B) into hole (G) Figs. 33 & 34, on belt unit. Tighten set screw (F) to hold support bar and table assembly in position. WARNING: THE TABLE EDGE (H) FIG. 34, MUST BE POSITIONED A MAXIMUM OF 1/16" AWAY FROM SANDING BELT (J) TO AVOID TRAPPING THE WORK OR FINGERS BETWEEN THE TABLE AND SANDING BELT. Fig. 33 A C B D E G Fig. 34 B F G E H J DUST SPOUT A dust spout (A) Fig. 35, is supplied with your sander and can easily be

Dust port (B) measures 2-1/4" I.D. AB Fig. 3 FASTENING SANDER TO SUPPORTING SURFACE IMPORTANT: IF DURING OPERATION THERE IS ANY TENDENCY FOR THE SANDER TO TIP OVER, SLIDE OR WALK ON THE SUPPORTING SURFACE, THE SANDER MUST BE SECURED TO THE SUPPORTING SURFACE USING FASTENERS THROUGH THE FOUR HOLES (C) FIG. 4. C C Fig. 4 4 CONNECTING DISC SANDER TO POWER SOURCE POWER CONNECTIONS A separate electrical circuit should be used for your tools. This circuit should not be less than #12 wire and should be

33 for use with a dust collection system. You must adjust the shield to suit your sanding operation. 1. If you are sanding with the disc, push in on the dust shield (A) Fig. 33. A Fig. 33 14 2. If you are sanding with the belt, pull the dust shield (A) Fig. 34 outward. A Fig. 34 WRENCH STORAGE A hole is provided in the stand for storing the hex wrench (A) Fig. 35, supplied with the sander. REMOVING UPPER SANDING A Fig. 35 DRUM GUARD You can remove the upper sanding drum guard (A) Fig. 36 to sand