• Enter the product model number in the Search function and click Search. •Click on the Manuals hyperlink. • Open the PDF of your choice and print the document. Contacting Agilent Assistance with test and measurements needs and information on finding a local Agilent office are available on the Web at: If you do not have access to the Internet, please contact your Agilent field engineer. NOTE In any correspondence or telephone conversation, refer to the Agilent product by its model number and ful

• The test set and associated equipment are connected as shown in Figure 2-9 on page 2-15. This chapter shows you how the network analyzer can be used to manually control the test set. The method presented here is considered a manual one because the user manually enters individual commands on a keyboard connected to the network analyzer. The chapter includes the following sections: • Preparing the Analyzer to Control the Test Set • How to Send a Manual Command • Common Errors in Manual Commands

Offices Asia-Pacific Agilent Technologies, Inc. 24/F, Cityplaza One, 1111 King’s Road, Taikoo Shing, Hong Kong, SAR Tel: (852) 3197–7777 Fax: (852) 2506–9284 Australia/New Zealand Agilent Technologies Australia Pty. Ltd. 347 Burwood Highway Forest Hill, Victoria 3131 Tel: 1 800 629 485 (Australia) Fax: (61 3) 9272 0749 Tel: 0 800 738 378 (New Zealand) Fax: (64 4) 802 6881 Canada Agilent Technologies Canada Inc. 5150 Spectrum Way Mississauga, Ontario L4W 5G1 Tel: 1 877 894 4414 Europe Agilent Tec

The library contains the following four subprograms. The library runs on HP BASIC. Load_vfp_data subprogram Loads data file (that was created and saved by Virtual Front Panel utility) to your program. The file contains all data from the 24 Setup Memories, and setup mode data for initializing the E5250A. Load_yfp_data(Address_5250,"LOAD FILE", Setup_data$) Address_5250: GPIB address of the E5250A. LOAD_FILE: File name of data you want to load. Setup_data$: Data string for internal use in th

r Products Tested The following Agilent instruments have been tested to operate properly with a PC, printer, and modem using the cable and adapter kits. • 33120A Function Generator /Arbitrary Waveform Generator • 34401A Multimeter • 53131A Universal Counter Cable and Adapter Pin Diagrams The following diagrams show the pin connections for the Null Modem cable (part number F1047-80002) with each of the adapters. Instrument DCD 1 - RX 2 - TX 3 DTR 4 GND 5 DSR 6 RTS 7 CTS 8 R

One reading is displayed for each monitor command. The Web interface can also be used to monitor a channel measurement. The 3499A/B/C monitor feature allows users to continuously monitor a selected switch or module status from the front display. A channel monitor can be set up using the front panel buttons or instrument commands. The 3499A/B/C monitor output can be a specific switching channel, a digital I/O port or the state of all switches or digital I/O on one plug-in module. The 3499A/B/C al

Static electricity can build up on your body and can easily damage sensitive internal circuit elements when discharged. Static discharges too small to be felt can cause permanent damage. Devices such as calibration components and devices under test (DUTs), can also carry an electrostatic charge. To prevent damage to the test set, components, and devices: • always wear a grounded wrist strap having a 1 MW resistor in series with it when handling components and devices or when making connections t

This will enable this folder as the shared folder. In the example below “PUBLIC” is Share directory. Same procedure applies for the Music and Video folders. On your Xbox 360, go to “Media” tab, select either Music or Pictures and press A button of the Xbox console to continue. Press X button of the Xbox console to change the source and select your network drive. It should show up as storagexxx and display the folder that you have set up earlier on your NAS adapter. Printer Server Inside the shar

See Figure 4-6. Agilent B2200 User’s Guide, Edition 4 4-21 Programming Capacitance Compensation In Figure 4-6, C2H, C2L, C3H, C3L are the compensation coefficients defined in the compensation data file. where, CxH is for the path connected to the Agilent 4284A Hc-Hp terminal, and CxL is for the path connected to the Agilent 4284A Lc-Lp terminal. When the Agilent B2220A probe card interface is used, obtain the coefficients for C3x, and create your compensation data file. In this case, probe

Government will receive no greater than Restricted Rights as defined in FAR 52.227-19(c)(1-2) (June 1987). U.S. Government users will receive no greater than Limited Rights as defined in FAR 52.227-14 (June 1987) or DFAR 252.227-7015 (b)(2) (November 1995), as applicable in any technical data. User’s Guide 5964-7333 Printing Copies of Documentation from the Web To print copies of documentation from the Web, download the PDF file from the Agilent web site: •Go to • Enter the product model number