< :> indicates the ‘or’ condition. For which user has a choice for the options listed within, and only one can be specified. <~> indicates the value range. For which user has a choice for the values within the range, and only one can be specified. <,> indicates a separation between integer values. ACCUSYS, INC. 5F, 38 TAIYUAN ST, JHUBEI, HSINCHU, TAIWAN, R.O.C. TITLE EXPERAID COMMAND LINE INTERFACE USER GUIDE PROJECT “DESKTOP RAID” DOCUMENT STATUS OFFICIAL RELEASE REV. G–05-NOV-2007 PAGE 11 OF 2

Up to two floppy disk drives can be connected to the host adapter. Note: The AMM-1572 supports only floppy primary address 3F0h - 3F7h. The IRQ channel is hard-wired for channel 6 and the DMA channel is hard-wired for channel 2. To connect floppy disk drives: 1 Connect one end of the 34-pin floppy ribbon cable to the floppy connector on the host adapter. Note: When cabling the 34-pin floppy ribbon cable to both the host adapter and floppy disk drive(s), make sure that Pin 1 orientation is ma

License. This Agreement grants you, the Licensee, a license to: a. Use the Software on a single computer system, which is not intended for use by more than five (5) users; and: b. Make one copy of the Software in machine readable form solely for back-up purposes, provided you reproduce Adaptec's copyright proprietary legends. Notwithstanding the foregoing, the Software may be used on the home, laptop or other secondary computer of the principal user of the Software, and an additional copy of the

AHA-1510A/20A Series host adapters give you access to Adaptec’s ASPI (Advanced SCSI Programming Interface) family of software. This family includes device drivers that work with tape, disk, CD-ROM, WORM, and DAT devices and also with operating systems such as DOS, OS/2, UNIX, and NetWare. The ASPI software communicates with the operating system managers through the common ASPI platform. AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAHA-1510A/20A Series User’s Guide A AA AA ASt

.. Disk storage and power connection for each drive. .. Static grounding strap or electrostatic discharge (ESD) safe work area. Optional items… Battery backup module to back up cached data in the event of a power failure. LCD Control Panel for Card status and advanced configuration. 2 Familiarizing yourself with the ACS- 61100 RAID Card 1. DDRII memory connector 6. PCI-Express x 8 connector 2. I2C connector 7. Serial port connector 3. Mini SAS connectors 8. Button port connector 4. Disk access L

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means; electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of Adaptec, Inc., 691 South Milpitas Blvd., Milpitas, CA 95035. Trademarks AMI is a registered trademark of American Megatrends, Inc. ASPI is a trademark of Adaptec, Inc. IBM PC-AT and OS/2 are registered trademarks of International Business Machines Corporation

691 South Milpitas Boulevard Milpitas, CA 95035 © 1998, Adaptec, Inc. All rights reserved. Adaptec and the Adaptec logo are trademarks of Adaptec, Inc. which may be registered in some jurisdictions. Printed in Singapore STOCK NO.: 511607-00, Rev. B BKB 12/97 t t t t SlimSCSI 1450 Adapter User’s Guide R t t t t Contents Introduction 1 Contents of Kit 1 System Requirements 1 Installing the SlimSCSI 1450 2 Updating the Windows 95 Miniport Driver 5 Using the SlimSCSI 1450 6 Hot Plugging 6 Formatting

Should one of the drives failed, parity data can be used to rebuild the failed data. Under RAID 5, parity data is stored across all drives in the array. This maximizes the amount of storage capacity available from all drives in the array while still providing data redundancy. RAID 5 requires at least three drives. The ACS-77100 allows user to set RAID 5 with three drives and the fourth drive as a hot-spare drive ready to be used for rebuilding data in case one of the other drives fails. The diag

8 If you selected options 1 or 3 in the previous step, go to step 9. If you selected option 2, type the LES ATM address at the ADPT> prompt. A series of messages appears, advising you that the following files will be or have been modified: PROTOCOL.INI CONFIG.SYS 9 If C:\WINDOWS is the name of your Windows directory, press Enter at the ADPT>C:\WINDOWS prompt. If Windows is located in a different place, type the correct drive:\directory name, and press Enter. The installation utility advises you

• Make sure that the SCSI boot drive address is set to SCSI ID 0:0. Check the drive installation manual for information about setting the SCSI ID for that device. The Return Installed Devices utility in the Onboard utilities can also be used to determine the SCSI addresses of peripherals on the SCSI bus. • Make sure that SCSI parity is consistently enabled or disabled on all devices on the SCSI bus. • Verify the proper installation and configuration of the host adapter and SCSI devices. • Power