Votes - , Average rating: ( )

User manual Hans Grohe, model SELECTRONIC 6068.22X

Manafacture: Hans Grohe
File size: 869.21 kb
File name:

Language of manual:

The document is loading, please wait

Download nowClose

The document is loading, please wait

Download nowClose

Fig. 4. 1. Clean the end of the supply pipe. Push the threaded ADAPTER (1) on until it is seated against the internal stop. Sweat the ADAPTER (1) to the pipe. 2. From behind the wall install the CONTROL STOP (2) to the water supply line with the outlet positioned as required. 3. Support piping as required. 3 FLUSH OUT SUPPLY LINES; Fig. 5 1. Open SUPPLY STOP (1). 3. Turn on water supply to flush line of any debris or sediment. 4. Close SUPPLY STOP (1) and turn off water supply line. Fig. 4 Fig. 3a Fig. 5 Fig.3 (TOP SPUD FIXTURE ILLUSTRATED) 1 3 2 2 1 1 *FOR HOLE LOCATION OF SUPPLY ON BACK INLET FIXTURES, REFER TO FIXTURE BEING INSTALLED FOR CORRECT HEIGHT FROM FINISHED FLOOR 127mm (5) 406mm (16 REF.) 127mm (5) TO P FILE EDGES CLEAN & SOLDER TO ADAPTER (1) 115mm-134mm (4-1/2 TO 5-1/4) CONTROL STOP DN 25mm (1" I.P.S.) CONTROL STOP OUTLET CLOCKWISE CLOSES CONTROL STOP COUNTER-CLOCKWISE OPENS CONTROL STOP TOP TO P 2 403 TO 441mm (15-7/8 MIN. TO 17-3/8 MAX.) 127mm (5 MAX.) M968550 REV. 1.6 3 44 INSTALL VACUUM BREAKER AND FLUSH CONNECTIONS; Fig. 6 1. Place the SPUD FLANGE (1) over the spud on the Fixture. Fig. 6. 2. Thread SPUD COUPLING NUT (2) onto Spud. Make sure SEAL WASHER (4) and FRICTION WASHER (3) are installed. Do not tighten fully. Fig. 6. 3. Remove the COUPLING NUTS (6, 6a) from the CHROME ELBOW (5). Make sure you have a TAPERED RUBBER WASHER (7), PLASTIC SUPPORT (8) and SQUARE SEAL WASHER (9). Fig. 6a. 4. Install the SQUARE SEAL WASHER (9) onto the PLASTIC SUPPORT (8) if not already installed. Insert the PLASTIC SUPPORT (8) into the DOWN TUBE (10). Slide the COUPLING NUT (6) onto the DOWN TUBE (10). Connect the COUPLING NUT (6) to the CHROME ELBOW (5) and tighten fully. Insert the DOWN TUBE (10) with CHROME ELBOW (5) into the SPUD COUPLING NUT (2) and push it down. Do not tighten fully. Fig. 6a. Note: If center line of ELBOW (5) cannot be adjusted to line up with hole in wall, then cut the DOWN TUBE (10) as required. 5. Measure and cut the HORIZONTAL TUBE (11) to length required. Important: Make sure that there is a minimum of 1-1/4" for engagement with elbow when making your measurement. Fig. 6b. 6. Remove the COUPLING NUT (14) from BRASS ELBOW (12) and slide it onto the HORIZONTAL TUBE (11). Install the SQUARE SEAL WASHER (13) onto the PLASTIC SUPPORT (15) if not already installed. Insert the PLASTIC SUPPORT (15) into the HORIZONTAL TUBE (11). Connect the COUPLING NUT (14) to the BRASS ELBOW (12) and tighten fully. Fig. 6b. 7. From behind the wall install the ELBOW AND TUBE ASSEMBLY (12, 11) through the hole in the wall. Install WALL ESCUTCHEON (16) onto HORIZONTAL TUBE (11). Assemble the COUPLING NUT (6a) and TAPERED RUBBER WASHER (7) in the CHROME ELBOW (5) onto the HORIZONTAL TUBE (11). Push the HORIZONTAL TUBE (11) into the CHROME ELBOW (5). Tighten COUPLING NUT (6a) but not fully. Fig. 6b. 8. For back spud installations: Follow steps #1 and #2 to install the spud coupling kit. Push the HORIZONTAL TUBE (11) into the spud connection on ...