Votes - 2, Average rating: 4 ( )

Manafacture: Pride Mobility File size: 6.69 mb File name: Language of manual:

Your Quantum Rehab Provider has evaluated your power chair and made any necessary adjustments to suit your specific requirements. Do not change your seating configuration without first contacting Pride Mobility Products or your Quantum Rehab Provider. WARNING! Some power chair components are heavy. You may need assistance to lift or carry them. Please refer to “Appendix I - Specifications” for specific component weights before you disassemble the power chair. WARNING! Remove the occupant from the power chair before making any adjustments. You may need the following to make comfort adjustments: .. metric/standard socket set and ratchet .. adjustable spanner .. thread lock Seat Height and Seat Angle Adjustment You can change the seat height to one of four positions by raising the front and rear trapeze bars. If you raise or lower only one trapeze bar (front or rear), you can also change the seat base angle (dump). To change the seat height: 1. Turn off the power to the controller. 2. Disconnect the controller connector(s) from the power base. See figure 7. 3. Flip up the seat latch safety. See figure 13. 4. Squeeze the seat latch and release the seat from the front trapeze bar. 5. Slide the seat forward and remove it from the power base. 6. Loosen the setscrews on the seat towers. See figure 14. 7. Loosen the screws that attach the trapeze bars to the seat posts. See figure 14. 8. Remove the retaining clips that secure the seat posts to the power base. See figure 14. 9. Move the trapeze bars up or down to the desired height. NOTE: Change the seat dump by raising or lowering only one set of towers (front or back). Figure 14. Seat Adjustment - Trapeze Bars RETAINING CLIPS SCREWS Figure 13. Seat Height Adjustment - Seat Latch Safety V. COMFORT ADJUSTMENTS V. COMFORT ADJUSTMENTS 10. Reinstall the retaining clips from step 8. 11. Remove each screw from the trapeze bars and apply thread lock. 12. Reinstall each screw into the trapeze bars and tighten. 13. Tighten the setscrew in each seat tower. See figure 14. 14. Reinstall the seat. 15. Lift the armrest straight up, then route the controller harness so that it cannot be pinched in the seat hinge. See figure 11. 16. Reconnect the controller to the power base. 17. Secure the controller harness with one or more wire ties. See figure 12. Seat Position Adjustment You can move the seat forward or rearward by changing the extrusion mounting position. To change the seat position: 1. Unplug the controller connector(s) from the power base. 2. Remove the seat from the power base. 3. Remove both extrusions from the bottom of the seat. 4. Reposition the extrusions on a different set of mounting holes. You must move both extrusions the same number of holes either forward or backwards. See figure 15. 5. Fasten the extrusions back onto the bottom of the seat. 6. Reinstall the seat. 7. Lift the armrest straight up, then route the controller harness so that it can not be pinched in the seat hinge. See figure 11. 8. Reconnect the controller. 9. Secure the controller harness with one or more wire ties. See figure 12. Manual Recline Seatback Adjustment If your power chair is equipped with a reclining seat, you can adjust the seatback angle with the seatback release lever. The lever is located on the right side of the seat base. See figure 5. To adjust the recline angle: 1. Pull up on the seatback release lever. 2. Lean forward or backwards to the desired position. 3. Release the lever. Figure 15. Seat Position Adjustment Quantum 614 Series V. COMFORT ADJUSTMENTS V. COMFORT ADJUSTMENTS Seatback Angle Adjustment If your power chair is equipped with an adjustable seat- back, you can adjust it to four (4) different angles: 90°, 102°, 105°, or 107°. To adjust the seatback angle: 1. Remove the adjusting screws from each seat hinge. See figure 16. 2. Set the seatback at the desired angle. 3. Reinstall the adjusting screws to each seat hinge and tighten. Armrest Width Adjustment You can change each armrest’s width independently of the other. NOTE: Changing the armrest width may increase theoverall width of your power chair. To change the armrest width: 1. Locate the two armrest knobs on each side of the armrest receiver bracket. See figure 16. 2. Loosen the knobs. 3. Slide the armrests in or out to the desired width. 4. Tighten the knobs. Armrest Angle Adjustment To change the armrest angle: 1. Lift the armrest straight up so that it is perpendicular to the floor. See figure 16. 2. Loosen the jam nut. 3. Turn the adjusting screw to raise or lower the front of the armrest. 4. Tighten the jam nut to lock the adjusting screw into place. Armrest Height Adjustment To change the armrest height: 1. Loosen the two setscrews located on the armrest receiver. See figure 16. 2. Raise or lower the armrest to the desired height. 3. Tighten the setscrews to secure the armrest. Figure 16. Seatback/Armrest Adjustment ARMREST KNOB JAM NUT SEATBACK ANGLE ADJUSTING SCREW ARMREST HEIGHT ADJU...

Download now

Please, enter two numbers from picture: