DUST COLLECTION S YS TEM FOR YOUR SAFETY: ° assembmy READ ALL INSTRUCTIONS ooperation CAREFULLY. "parts o repamr Sold by SEARS, ROEBUCK AND CO., Chicago, IL. 60684 U.S.A. Part No. SP5373 Printed in Taiwar_ • • •:• •_:-•-::_:/.'-• ••• ,.,. ,,i _. FULL:ONEYEAR WARRANTY ON CRAFTSMAN DUST C-OLL_ If within 0ne year from the date of purchase, thls Craftsman Dust Collection System falls due to a defect in maierlal0r workmanship;Searswil!repair it,freeofcharge; WARRANTY SERVICEIS AVAILABLE BY SIMPLY CON

320.48291 CAUTION! Before using this • Safety product, read this manual and , Operation follow all its Safety Rules ° Magstlc ® and Operating Instructions. ° Maintenance Sears Brands Management Corporation www, craftsman.com Warranty Page2 Safety instruction Page3 Description Page4 Operation Instructions Page6 Applications Page 11 Maintenance Page 14 Troubleshooting Page 15 Parts List Page 15 ONE YEAR FUt.L WARRANTY ON CRAFTSMAN®PRODUCT If this Craftsman product fails due to a defect in material

Model Number: Model Description: *Product you purchased may vary from picture shown* CAUTION: Read and follow all Safety Rules and Operating Instructions of this product. Retain this document for future reference. Sears, Roebuck and Co., Hoffman Estates, IL 60179 USA • DO NOT stand on this product. You may fall which may cause personal injury. • WEAR SAFETY GLASSES AND GLOVES when cutting the banding material. The bands may snap which may cause personal injury. • WEAR SAFETY GLASSES when removin

unit the and line up with lock. Insert • Remove (4) screws holding top in the lock rod into the back of the lock. Chain place. • Test lock operation. Lever Style -Lift or • Lift top off of unit enough to reach the • Reinstall drawers. lower (depending on the wiring harness. slide) the release lever • Reinstall work surface. • Disconnect wiring harness from unit. • Reconnect power to the unit. on both sides, (this allows the slides to ride • Remove top from unit. over the stops.) Pull out to remo

• Remove enough drawers to reach the top back inside of the unit. (See Drawer installation and removal.) • Push actuator rod to back of unit to disconnect from back of lock. Move actuator rod for access. • Remove (4) screws holding top in place. • Lift top off of unit enough to reach the wiring harness. • Disconnect wiring harness from unit. • Remove top from unit. Press to release Chest Top Installation • Connect wiring harness to top. • Position top on unit. • Attach using (4) screws. • Make s

Feeding the tool in the wrong direction, causes the cutting edge of the bit to climb out of the work and pull the tool in the direction of this feed. If the workpiece or bit becomes jammed or bogged down, turn the tool “OFF” by the switch. Wait for all moving parts to stop and unplug the tool, then work to free the jammed material. If the switch to the tool is left “ON” the tool could restart unexpectedly causing serious personal injury. Do not leave a running tool unattended, turn power off. On

Los accesorios pueden resultardafiadosduranteeltransporteo elmanejoy puedensalir despedidos al ganar velocidad. Esto no escornish,perosf sucede. Practiqueprimero enmaterialesde desechoparaver c6mocorta laherramientagiratoria.Tengaencuenta queel trabajo es realizadopor la velocidad deta Paratenermejor controlal realizartrabajofino, agarre laherramientagiratoriacomo unI_pizentreeldedo pulgary eldedo indice. herrarnientay porelaccesorioqueseencuentraenel portaherramienta. Usted no debe apoyarsesobr

To maintain balance on abrasive wheel points, before each use, with the wheel point secured in the collet, turn on the Rotary Tool and run the Dressing Stone lightly against the revolving wheel point. This removes high spots and trues up the wheel point for good balance. The hanger is provided for the use of hanging your tool while using the flex-shaft or for storage. If you do not use the hanger, remove it from the tool and snap it back into place underneath the cord so it will be out of the wa

° Espa_ol Sears, Roebuck and Co., Hoffman Estates, IL 60179 2610913327 Table of Contents Page Warranty ........................................................ 2 Power Tool Safety Rules .......................................... 3-6 Symbols ........................................................ 7 Functional Description and Specifications ............................ 8-9 Assembly .................................................... 10-11 Operating Instructions ..................................

CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. 14. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacem